Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 27

Страница: 27 / 147

Using OmniStream

™

with Velocity

™

Device Manager

• Verify that all encoders and decoders are set to the same system mode. In this tutorial, both encoders and the

decoder should be set to

VCx

. Refer to

Setting the System Mode (page 16)

• Go to the

INPUT

menu and verify the folllowing. Refer to

Configuring Inputs (page 17)

for more information.

Make sure that the

Cable Present

indicator, under the

HDMI Input 1

window group, is green.

Make sure the

Input

drop-down list is assigned to an input. In this tutorial, the

Input

field for both encoder 1

and encoder 2 are set to

HDMI Input 1

Verify that the

Max bit rate

field is set to at least

450

Verify that a

Thumbnail

Enable

toggle switch is enabled and a thumbnail of the source is displayed. When

enabled, the toggle switch will be green.

• Go to the

SESSION

menu and verify the following under the

Stream 1

window group. Refer to

Creating a

Session (page 20)

for more information.

Make sure the

Interface

field for both encoders is set to

eth1

Verify that the

Encoder

field is set to

Encoder 1

Check that the

Scrambling

toggle switch is enabled (green). Also check that the

Key

field, for this example,

is set to

scrambling

for both encoders.

Verify that the

Video

Video Enable

toggle switch is set to enabled for both encoders.

Check the

Video

Destination Multicast/Unicast Address

field is set to the correct multicast IP address.

In the example,

226.0.0.1

. is used on encoder 1 and

226.0.0.2

is used on encoder 2.

Check that the

Video

Destination UDP

Port

field is set to the proper port. In this example,

1000

should

be used on both encoders.

Make sure the

Audio

Source

is set to

HDMI 1

on both encoders.

Verify that the

Audio

Enable Audio

toggle switch is enabled on both encoders.

Check the

Audio

Destination Multicast/Unicast Address

field is set to the correct multicast IP address.

In this example,

226.0.10.1

is used on encoder 1 and

226.0.10.2

is used on encoder 2.

Check that the

Audio

Destination UDP

Port

field is set to the proper port. In this example,

1100

is used

for both encoders.

If no video and/or audio is present on the display, check the following

Encoder Checklist

Basic Configuration Tutorial

Troubleshooting

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды