Panasonic WV-SPN311 Скачать руководство пользователя страница 131

Страница: 131 / 218

If further adjustments are required, repeat from step 2.

Note

•

“Audio detection” can only be used when “Mic input” or “Interactive(Full-duplex)

S P N311

” is selected

for “Audio transmission/reception” on the [Audio] tab of the “Image/Audio” page. (

page 111)

•

Noise or other unwanted sound from the surrounding area may be mistakenly detected.

•

Only the volume of the sound determines whether sound is detected or not, the type of sound does
not matter.

13.7 Configuration of the settings relating to alarm
notification [Notification]

Click the [Notification] tab on the “Alarm” page. (

page 41, page 43)

The settings relating to Panasonic alarm protocol and HTTP alarm notification can be configured in this section.

Operating Instructions

131

13 Configure the alarm settings [Alarm]

Содержание WV-SPN311



























































































































































































































Результаты поиска

Содержание WV-SPN311

Отзывы:

Бренды по названию

Популярные бренды

Panasonic WV-SPN311, Руководство по эксплуатации

Результаты поиска

Содержание WV-SPN311

Отзывы:

Бренды по названию

Популярные бренды