Panasonic WV-SFV310 Скачать руководство пользователя | Manualshive

Страница: 106 / 212

background image

11.11 Configure the settings relating to audio
[Audio]

SF x311

SF x311

SFN310

SFN310

Click the [Audio] tab on the “Image/Audio” page. (

®

page 40, page 42)

The settings relating to audio can be configured on this page.

Note

•

Images and audio will not be synchronized. Therefore, images and audio may not always match.

•

Audio may be interrupted depending on the network environment.

•

Recording will stop if the settings of audio are configured during recording.

[Audio transmission/reception]

Select the communication mode used for audio data transmission/reception between the camera and the PC
from the following.

•

Off:

SF x311

SF x311

SFN310

SFN310

Does not receive/transmit audio between the camera and the PC. Therefore, the

settings and controls relating to audio will be invalidated.

•

Mic input:

SF x311

SF x311

SFN310

SFN310

The PC receives audio data from the camera. Audio can be heard with

images on the PC. Images and audio will not be synchronized.

•

Audio output:

SF x311

SF x311

Audio data from the PC will be transmitted to the camera. Audio can be heard

from the speaker connected to the camera.

•

Interactive(Half-duplex):

SF x311

SF x311

Both reception and transmission are available. However, audio data

cannot simultaneously be transmitted and received.

•

Interactive(Full-duplex):

SF x311

SF x311

Both reception and transmission are simultaneously available.

•

Default:

Off

Note

•

Howling may be generated depending on usage conditions. If howling is generated, prevent sound
generated by the PC from entering the PC microphone.

•

When “Multicast” is selected for “Transmission type” on the [JPEG/H.264] tab of the “Image/Audio”
page, audio transmission will become unavailable while monitoring H.264 images. To transmit audio
from a PC to the camera, click the [JPEG] button on the “Live” page.

•

“Audio recording” and “Audio detection” only operate when “Mic input” or “Interactive(Full-duplex)” is
selected for “Audio transmission/reception”.

106

Operating Instructions

11 Configure the settings relating to images and audio [Image/Audio]

«
...
104
105
106
107
108
...
»

Содержание WV-SFV310





















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WV-SFV310

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 4

WV-CP300 Series

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 25

WV-NP240 series

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 20

OneHome KX-HCM110A

Бренд: Panasonic Страницы: 4

OneHome KX-HCM110A

Бренд: Panasonic Страницы: 24

WVCP230 - CCD 120V

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Super Dynamic III WV-CW964

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды