Step3
Fixing the camera
Step2
Making connections
WV-X6531N
fles0217-2077 PGQX2158XA Printed in China
WV-X6531N
Network Camera
Model No.
WV-X6531N / WV-X6511N
/ WV-S6530N
Installation Guide
Included Installation Instructions
• Before attempting to connect or operate this product, please read these instructions carefully and
save this manual for future use.
• Before reading this manual, be sure to read the Important Information(included in the CD-ROM).
• For information about how to perform the settings and how to operate the camera, refer to the
Operating Instructions on the provided CD-ROM.
• The model number is abbreviated in some descriptions in this manual.
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic Corporation
Osaka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Panasonic Corporation 2017
The model number and serial number of this
product may be found on the surface of the unit.
You should note the model number and serial
number of this unit in the space provided and
retain this book as a permanent record of your
purchase to aid identification in the event of
theft.
Model No.
Serial No.
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction man-
ual, may cause harmful interference to radio com-
munications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interfer-
ence at his own expense.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables
when connecting to computer or peripheral devic-
es). Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate this
equipment.
For U.S.A.
CAN ICES-3(A)/NMB-3(A)
For Canada
WARNING:
• To prevent injury, this apparatus must be secure-
ly attached to the wall/ceiling in accordance with
the installation instructions.
• All work related to the installation of this product
should be made by qualified service personnel
or system installers.
• The installation shall be carried out in accor-
dance with all applicable installation rules.
• The connections should comply with local elec-
trical code.
• This equipment is compliant with Class A of
CISPR 32. In a residential environment this
equipment may cause radio interference.
• Batteries (battery pack or batteries installed)
shall not be exposed to excessive heat such as
sunlight, fire or the like.
CAUTION:
• Any changes or modifications not expressly
approved by the party responsible for compli-
ance could void the user’s authority to operate
the equipment.
• The network camera is only intended for a con-
nection to an ethernet or PoE+ network without
routing to the outside plant.
Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them
to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment.
For more information about collection and recycling, please contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
Note for the battery symbol (bottom symbol)
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
: Direct current symbol
: Alternating current symbol
Important safety instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
6) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
7) Only use attachments/accessories specified by the manufacturer.
8) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
S3125A
9) Unplug this apparatus during lightning storms or when unused for long periods of time.
10) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been dam-
aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
Troubleshooting
Open Source Software
• This product contains open source software licensed under GPL (GNU General Public License), LGPL
(GNU Lesser General Public License), etc.
• Customers can duplicate, distribute and modify the source code of the software under license of GPL and/
or LGPL.
• Refer to the “readme.txt” file on the provided CD-ROM for further information about open source software
licenses and the source code.
• Please note that Panasonic shall not respond to any inquiries regarding the contents of the source code.
Before requesting service, refer to the Important Information (included in the CD-ROM) and “Troubleshooting”
in the Operating Instructions (included in the CD-ROM) and confirm the trouble.
The following notations are used when describing the functions limited for specified models. The functions
without the notations are supported by all models.
X6531
X6531
:The functions with this notation are available when using the model WV-X6531N.
X6511
:The functions with this notation are available when using the model WV-X6511N.
S6530
:The functions with this notation are available when using the model WV-S6530N.
About notations
Preparations
Other items that are needed (not included)
Prepare the required parts for each installation method before starting the installation. The following
are the requirements for the various installation methods.
Installation method
Mounting
screw
Minimum pull-out
strength*
1
A
When hanging the camera from ceiling
Use the ceiling mount bracket (WV-Q121B
*2
).
M10 screws/
4pcs.
1411 N {317 lbf}
B
When installing the camera on a wall
Use the wall mount bracket (WV-Q122A
*2
).
M10 screws/
4pcs.
823 N {185 lbf}
IMPORTANT:
• Prepare four mounting screws (M10) to be mount-
ed on ceiling and wall separately.
• Select screws according to the material of the
location that the camera will be mounted to. In this
case, wood screws and nails should not be used.
• If the mounting location such as plaster board is
too weak to support the total weight, the area shall
be sufficiently reinforced.
IMPORTANT:
• The mount bracket (locally procured) should have the configuration that enables
fixation of safety wire from camera.
⇒
Go to Step 1
【
1
】
.
WV-Q122A
WV-Q121B
A
B
Preparations before installation
【
1
】
Prepare the cables from camera side.
◆
When the only necessary connection to
camera is an Ethernet cable
Use only RJ45 network cable coming from camera.
Do not remove the cable case. Use it as it is.
◆
When using 24 V AC, EXT I/O device, or
audio I/O device
Remove the cable case fixed by five screws on the
upper part of camera and pull out power cable,
audio I/O cable, and alarm I/O cable stored in it.
Note:
• Do not use the removed cable case and five
screws.
RJ45 (female)
Network
cable
Alarm input/
output·
Audio input/
output cable
Power
cable
Cable case
Main sunshield
rear cover
【
2
】
Insert an SD memory card (locally
procured) as occasion demands.
* SDXC/SDHC/SD memory card is described as
SD memory card.
Insert an SD memory card following the procedure
shown below. For the detailed procedure, refer to
Important Information on the provided CD-ROM.
①
Remove the main sunshield rear cover.
②
Loosen two locking screws of water-resistant
cap and pull the water-resistant cap and
toward you.
③
Insert an SD memory card into the SD
memory card slot.
④
Attach water-resistant cap and sunshield rear
cover to the original position in order.
Recommended tightening torque of the water-
resistant cap locking screws:
0.69 N·m {0.51 lbf·ft}
SD memory
card slot
SD memory
card (with
label side
facing down)
Water-resistant cap
*1 The minimum pull-out strength is the value per screw.
*2 For details on procedure for attaching mount bracket
and camera, read the operating instructions of each
mount bracket.
◆
When using Q121B (option) or Q122A (option)
⇒
Go to Step 1
【
3
】
.
◆
When using the mount bracket (locally procured).
Prepare a mount bracket.
The following figure shows an example of the camera mounted on a ceiling with a bracket.
R 1-1/2, 11crest, deep 30 MAX
(taper pipe thread)
RP 1-1/2, 11 crest,
deep 30 MAX
(parallel pipe thread)
60 mm {2-3/8 inches}
25 mm {31/32 inches}
85 mm {3-11/32 inches}
(fl
58)
Installation
The installation tasks are explained using 4 steps.
⇨
⇨
⇨
Step1
Fix the mount bracket
and hang the camera
Step4
Configure the network
settings
• Remove the camera using the reverse order of the installation procedures.
IMPORTANT:
• After waterproofing the hole for fixing mount
bracket and the port for pulling out the cable
on the installation surface, fix the mount
bracket on the installation surface.
• Adjust the length of cable from camera
attachment port of attachment pipe to cable
end to 150~160mm {5-29/32 inches~6-5/16
inches}. (If the cable that is pulled out is too
long, storage after wiring becomes difficult.
Adjust the cable length carefully.)
• For the number of fixing screws and the
minimum pull-out strength (per 1 pc.), refer to
the operating instructions of mount bracket
(locally procured).
• Ensure the minimum pull-out strength (per
1 pc.) that has sufficient allowance for total
mass of mount bracket (locally procured),
attachment pipe, and camera etc.
⇒
Go to Step 1
【
5
】
.
Step1 Fix the mount bracket and hang the camera
The following explains an example of installation using mount
bracket (locally procured).
The right figure shows an example of the camera mounted on a ceiling with a
mount bracket (locally procured).
When waterproofing, use waterproof material to fill in gaps and holes
between the attachment pipe and the mount bracket.
【
1
】
Fix the attachment pipe (accessory) to the mount bracket
(locally procured).
①
Fix the attachment pipe to the mount bracket.
②
Fill the gap between the mount bracket and attachment pipe with
waterproof material (locally procured) such as silicon clay.
③
Pass the cables from the ceiling through the mount bracket.
【
2
】
Fix the mount bracket (locally procured) on the installation surface.
Fix a mount bracket to the installation surface on the ceiling by using appropriate bolts,
nuts or the like (locally procured).
150~160mm
{5-29/32 inches~
6-5/16 inches}
About the user manuals
Product documentation is composed of the following documents.
• Installation Guide (this document and additional leaflet):
Explains installation, mounting, cable connec-
tions, and network connections. This manual uses the WV-X6531N as an example in the explanations.
• Important Information (included in the CD-ROM):
Provides basic information about the product.
• Operating Instructions (included in the CD-ROM):
Explains how to perform the settings and how to operate
this camera.
Adobe
®
Reader
®
is required to read these operating instructions on the provided CD-ROM.
When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the Adobe web site
and install it.
The external appearance and other parts shown in this manual may differ from the actual product within the
scope that will not interfere with normal use due to improvement of the product.
Standard accessories
Installation Guide
(this document and additional leaflet) .................. 1 pc.
IMPORTANT SAFETY INSTRUCTIONS ............... 1 pc.
Warranty card ..................................................... 1 pc.
CD-ROM*
1
.......................................................... 1 pc.
Code label*
2
........................................................ 1 pc.
*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.
*2 This label may be required for network management. Use caution not to lose this label.
Waterproof tape
*3 The screws are necessary when installing the camera on a separately sold mount bracket.
Cable cover ........................................................ 1 pc.
Attachment pipe ................................................. 1 pc.
Front/rear sunshields ...........................................1 set
Front/rear sunshields fixing screw
........................................ 2 pcs. (of them, 1 for spare)
Waterproof tape .................................................. 1 pc.
RJ45 waterproof connector cover ...................... 1 pc.
RJ45 waterproof connector cap ......................... 1 pc.
8P alarm cable ................................................... 1 pc.
24 V AC power supply connector kit ....................1 set
(Power supply connector housing: 1 pc., Contact: 3 pcs.)
Hexagon screw (M5)
*3
........................................ 5 pcs.
(of them, 1 for spare)
Rain wash coating caution label ...........................1 pc.
The following parts are used during installation procedures.
＊
For step 4, refer to
other leaflet
⇨
⇨
②
150~160mm
{5-29/32 inches~
6-5/16 inches}
③
①
Attachment pipe
(accessory)
Mount bracket
(locally procured)
Waterproof
material
Please read "Precautions for installation" of "Important Information" in the
provided CD-ROM closely before starting installation/connection of the camera.
Attachment
pipe
(accessory)
