67
Configure the settings and operations relating to the system
[System management]
The settings relating to the actions at an error occurrence and auto data deletion from hard disk drives can be
configured on this tab. It is also possible to display the logs on this page. In addition, general maintenance,
such as license registration, setting initialization and firmware upgrade, can be performed on this tab.
■
System setup
[Error output duration]
Select the duration to output a signal to notify the
external devices of an error (HDD error, camera error,
recorder error, recording error or network error).
When "0 s" is selected, the signal is not output.
0 s/ 2 s/ 5 s/ 10 s/ 20 s/ 30 s/ 1 min
Ext.: When "Ext." is selected, the signal will keep
on being output until the error is reset.
Default:
2 s
Note:
• Refer to the "Cancel the error action" section
(
☞
Page 129) for how to reset the error.
[Error buzzer duration]
Configure the settings to sound a buzzer at an error
occurrence. When "0 s" is selected, buzzer will not
sound.
0 s/ 2 s/ 5 s/ 10 s/ 20 s/ 30 s/ 1 min
Ext.: When "Ext." is selected, the buzzer that
started sounding at an error occurrence will
keep on sounding until the buzzer is stopped.
Default:
2 s
Note:
• Refer to the "Stop buzzer beeping" (
☞
for further information about how to stop buzzer
beeping.
[Safe shutdown time]
Set time to start the power outage process after the
power failure detection signal is input to the recorder.
10 s/ 20 s/ 30 s/ 1 min/ 2 min/ 3 min/ 4 min/ 5 min
Default:
10 s
[HDD stand-by control mode]
Set a mode not to count the operation time of a hard
disk drive (HDD stand-by control mode) by temporar-
ily pausing HDDs other than those which are record-
ing or waiting for recording.
On: Operates in the HDD stand-by control mode
Off: Operates in the normal mode.
Default:
Off
Note:
• In Single mode, it is effective when it consists of 3
or more HDD.
• In Mirroring (RAID1) mode, it is effective when it
consists of 6 or more HDD.
• In RAID5/RAID6 mode, it is effective when it con-
sists of 3 units or more.
• It may take time to play the data in the inactive
HDD during the HDD stand-by control mode.
• During the HDD stand-by control mode, the date
will not be displayed in white on the calendar of
the date and time operation panel even if there is
a recorded image (
☞
• The number of recording event search (
☞
not displayed during the HDD stand-by control mode.
[HDD hour meter warning]
If the operation time of a hard disk drive reaches a
specified level, a warning will be performed. When
"Off" is selected, warning will not be performed.
Off/ 10000 h/ 20000 h/ 30000 h/ 40000 h/ 50000 h
Default:
20000 h
[Auto data delete]
Select to determine how many days should have
passed from the recorded day to delete data auto-
matically from the hard disk drive.
Off/ 1 day/ 2 days/ 3 days/ 4 days/ 5 days/ 6
days/ 7 days/ 8 days/ 9 days/ 10 days/ 14 days/
30 days/ 45 days/ 60 days/ 90 days/ 120 days/
150 days/ 180 days/ 184 days
Default:
Off (Does not delete the data automatically.)
[Camera time auto synchronization]
When a date changes, the clock of the cameras will
be synchronized with the clock of this product.
On: Synchronized
Off: Not synchronized
Default:
On
[Setup via recorder's main monitor]
