Panasonic VB-44210G Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 394

background image

Chapter 3. System Features

Section 700 - Operation

Page 3-16

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Centrex/PBX Compatibility

(CPC-A Version 3.2 or higher, CPC-AII, and CPC-B Version 2.1 or higher)

Description

Centrex/PBX Compatibility allows the DBS to be connected to centrex or
PBX lines.

The DBS supports up to 8 access codes for dialing centrex or a PBX. These
access codes allow the DBS SMDR output to exclude the number dialed to
reach a centrex or PBX line.

The DBS also supports transmission of a flash signal over the centrex or PBX
link.

Related Programming

• FF1 (System): PBX Access Code(s)

• FF2 (Trunks): Trunk Type

• FF8 (Least Cost Routing): LCR Add Tables

Considerations

• The LCR Add Table can be used to prefix digits for outgoing calls through

Centrex.

Direct Inward Dialing (DID)

(CPC-B Version 2.0 or higher)

Description

The Direct Inward Dialing (DID) feature allows an extension to have a
dedicated direct number. The dedicated number allows calls to be made
directly to the extension, without the caller going through the attendant.

Prior to CPC-B Version 3.1, only one DID number could be assigned to an
extension. Beginning with CPC-B Version 3.1, one DID number can be
assigned to several extensions, and one extension can have more than one
DID number; this is also true of CPC-AII.

If a DID number is assigned to more than one extension, incoming calls to the
DID number ring at all the assigned extensions simultaneously.

«
...
60
61
62
63
64
...
»

Содержание VB-44210G











































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VB-44210G

Бренд: Easiphone Страницы: 13

Бренд: Earthworks Audio Страницы: 3

FUSION Apollo MS-WB670

Бренд: Garmin Страницы: 44

Бренд: AeroAudio Страницы: 8

Бренд: TANDBERG Страницы: 12

Бренд: Zhong Shan Anders Electronics Страницы: 5

Бренд: IBM Страницы: 84

Business Analog Telephone

Бренд: Tekelec Страницы: 145

Бренд: Motorvac Страницы: 16

Бренд: SONIQ Страницы: 7

Бренд: One Talk Страницы: 26

Бренд: Radio Shack Страницы: 44

Бренд: Work Pro Страницы: 12

Бренд: Uniden Страницы: 33

Бренд: AdvanceTec Страницы: 8

Бренд: Kenwood Страницы: 26

Бренд: Kenwood Страницы: 32

Бренд: Kenwood Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды