Panasonic VB-44210G Скачать руководство пользователя страница 320 | Manualshive

Страница: 320 / 394

background image

Appendix A. EX 1.0 Feature Update

Section 700-Operation

Page A-30

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Enhanced Programming Addresses

Enhanced programming addresses have been added to support T1 Networking. These
addresses are applicable only in a networked environment and can be ignored in a stand-
alone (non-networked DBS). Refer to the T1 Networking Reference Guide for detailed
information.

Modification to Toll Restriction Service

Description

The program address for TRS Operator Access (FF7 1# 18#...) has been
modified to allow an extension to dial “0+NXX” phone numbers, even if
“0-only” dialing is denied.

Four settings are possible.

Programming

See

Section 400 - Programming (Appendix C)

for more detailed

programming information.

Notes

• The Operator Access address applies only to DBS systems using the

(1995) NANP dialing plan (FF7 1# 17# 1#), and to TRS types 2-6 (TRS
types 0 and 1 do not allow outbound dialing; TRS type 7 allows all
dialing).

• If “0-only”, “00-only”, “10XXX0-only”, or “101XXXX0-only” calls

are restricted (settings 0 or 2), the system will wait 6 seconds before
automatically disconnecting the call. However, if the user dials
additional digits within 6 seconds, the DBS will check other switches to
determine whether to allow or deny the call.

• For all settings (0-3), the system will check the Equal Access Code

Format switch (FF7 1# 21#...) if a CIC (carrier identification code) is
dialed to reach a preferred inter-exchange carrier.

• For all settings (0-3), the system will check the international calls

switches (FF7 1# 1# and FF7 1# 19#) if “01”, “10XXX01”, or
“10XXXX01” is dialed.

• For settings 2 and 3, the system will not consider TRS settings for the

trunk.

«
...
318
319
320
321
322
...
»

Содержание VB-44210G











































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VB-44210G

Бренд: Nelson Страницы: 12

Бренд: ZF Страницы: 28

Бренд: York Страницы: 6

Бренд: Magnavox Страницы: 26

Бренд: Aastra Страницы: 16

Бренд: EasyPro Страницы: 8

Бренд: Karel Страницы: 24

Бренд: Uniden Страницы: 12

Clarity Extra W1100

Бренд: Walker Страницы: 27

Бренд: Facebook Страницы: 5

Clear Sound CL455

Бренд: Geemarc Страницы: 64

XDECT 8005WP Series

Бренд: Uniden Страницы: 12

Бренд: iTrak Страницы: 6

EASY CLEAR EQ-12-TH

Бренд: Bunn Страницы: 2

ETR 2000 series

Бренд: Delco Страницы: 34

Бренд: Radio Shack Страницы: 32

Бренд: Uniden Страницы: 7

Бренд: VTech Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды