Panasonic Varicam 35, Руководство по эксплуатации

Страница: 164 / 174

– 164 –
Chapter 14 Maintenance — Warning system
Display Description Behavior and cause
[HIGH TEMPERATURE]
The temperature inside the camera is higher than that of
the normal conditions.
f
The current operation will continue.
f
Turn off the power of the camera, turn it on again,
and check recording and playback operations. If the
problem persists, consult your dealer.
[PB INTERMITTENT] (slot number)
Playback is interrupted on the SDHC/SDXC memory
card. A card whose playback performance cannot be
assured is inserted.
f
The current operation will continue.
f
Use of microP2 or P2 memory card is recommended.
[PROXY ERROR] An error occurred in the internal proxy module.
f
The current operation will continue.
f
Turn off the camera and turn on it again to check the
recording and playback. If the error continues to occur,
please consult your dealer.
[PROXY REC WARNING] A proxy data recording error occurred.
f
The current operation will continue.
f
Turn off the camera and turn on it again to check the
recording and playback. If the error continues to occur,
please consult your dealer.
[REC IMPOSSIBLE] (slot number)
An SDHC/SDXC memory card is inserted into the
microP2 memory card slot.
Recording to the SDHC/SDXC memory card is disabled.
f
The current operation will continue.
f
Record to microP2 or P2 memory cards.
[REC WARNING]
[FRAME SIGNAL]
Displayed when a video or audio error occurs during
recording.
f
Warning lamp flashes four times per second during
continuous recording.
f
The current operation will continue. When input
signals are disrupted, recording continues while
disrupted images are recorded. Check the signal to be
input to the camera.
f
Turn off the power and on before using it again.
[REC WARNING]
[OVER MAX# CLIPS]
Displayed when attempting to record in excess of the
maximum total number of clips allowed for one P2 card.
f
Warning lamp flashes four times per second during
continuous recording.
f
The operation will stop.
f
Replace the P2 card or delete unnecessary clips.
[REC WARNING]
[PULL DOWN]
(Occurs during recording)
The video pull-down sequence and time code values
are not synchronized.
f
Warning lamp flashes four times per second during
continuous recording.
f
The current operation will continue.
f
Check the signal.
[REC WARNING]
[PULL DOWN ERROR]
(Occurs at times other than during recording)
The video pull-down sequence and time code values
are not synchronized.
f
The current operation will continue.
f
Check the signal.
[REC WARNING]
[REC DATA]
Displayed when an error occurs in recorded data during
recording.
f
Warning lamp flashes four times per second during
continuous recording.
f
The operation will continue or stop.
f
Turn off the power and on before using it again.
[RUN DOWN CARD] (slot number)
The maximum number of overwrites has been
exceeded.
f
The current operation will continue.
f
Replacement of the P2 card is recommended.
[SD CARD] (slot number)
An SDHC/SDXC memory card is inserted into the
microP2 memory card slot.
f
The current operation will continue.
f
Use of microP2 or P2 memory card is recommended.
[TEMPORARY PAUSE]
[IRREGULAR SIG]
Recording is temporary suspended due to correct
recording not possible because of the disruption of input
signal from the <GENLOCK IN> terminal. The clip will
be divided.
f
Warning lamp flashes four times per second during
continuous recording.
f
The operation will pause.
f
Recording will resume when the signal returns to
normal.
During thumbnail and menu operation
Display Description Behavior and cause
[AUTHENTICATION ERROR!] Manual authentication failed. Enter the correct password.
[CANNOT ACCESS!]
Data cannot be accessed due to a content defect or
some other reason.
Ensure the health of the media and the clips.
[CANNOT CHANGE!]
For a clip with the mark, where a thumbnail cannot
be generated, the thumbnail cannot be modified in the
text memo position.
Correct the settings and content to enable display of the
thumbnail.
[CANNOT DELETE!] The content versions do not match. Cannot delete. Match the device and contents version.
[CANNOT FORMAT!]
A P2 card problem or some other reason prevents
formatting.
Check the P2 card.
[CANNOT RE-CONNECT!]
Clips cannot be remerged because either clips not
recorded across multiple P2 cards are selected or other
reasons.
Check the selected content.
[CANNOT REPAIR IN SELECTION!] Some of the selected clips cannot be repaired. Check the selected content.
[CANNOT REPAIR!] Content that cannot be repaired is selected. Check the selected content.
[CANNOT SAVE! FILE NAME IN USE]
A settings file of the same name exists on the SD
memory card.
Use another name to save the file.
[CARD FULL!] The P2 card or SD memory card is full. Insert a card with free space available.