manualshive.com logo in svg

Panasonic TX-29EG20RU-IRAN, Руководство по обслуживанию, Страница: 7 / 31

Поделиться
Скачать
Panasonic TX-29EG20RU-IRAN Скачать руководство пользователя страница 7

4.1.1. +B Voltage

Item / preparation

 1. Operate the TV set.
 2. Set control as follows :

Brightness ........... minimum
Contrast ............... minimum

Adjustment procedure

 1. Confirm the DC voltage at the indicated test points, as

follows :
TPA 15 : 3.35 ± 0.2V
TPA 16 : 141 ± 2V
TPA 17 : 8.2 ± 0.3V
TPA 18 : 1.9 ± 0.2V
TPA 19 : 5.2 ± 0.2V
TPA 20 : 220 ± 15V

 1. Set Bright and Contrast controls to their maximum

positions.

 2. Operate the TV set over 60 minutes.
 3. Full degauss the picture tube by using an external

degaussing coil. By rotating R-B static convergence
magnet.

4.1.2. High Voltage

Item / preparation

 1. Receive the crosshatch pattern.
 2. Set to 0 Beam.

Screen VR .......... minimum
Contrast .............. minimum

Adjustment procedure

 1. Connect a DC voltage meter to D866 and confirm the +B

voltage is 141.0 ± 2V.

 2. Connect a high frequency voltmeter to heater and confirm

that voltage reads 6.3 ± 0.28 (VRMS).

 3. Normalize the brightness and contrast.

4.1.3. NTSC TINT COLOUR

Item / preparation

 1. Connect oscilloscope probe to TPL1 (R OUT) with 10k

Ω

series resistor.

 2. Press Main Menu and set system to use AV-NTSC (3.58

MHz).
DYNAMIC ................... Normal
Channel CLR Set ..... STD

Adjustment procedure

 1. Adjust Sub-Tint so that No. 2, 3 and 4 becomes level

waveform is similar to Fig. 3.

 2. Confirm phase at Tint is changes more than ± 15 by Tint

control.

 3. Confirm that colour level is maximum when colour DAC is

adjusted to maximum position.

Note:

Use remote control only when adjusting user mode to

Sub-Tint.

 4. Apply a crosshatch pattern signal and adjust roughly the

static convergence magnets.

 5. Apply a green pattern signal.
 6. Loosen a clamp screw for the Deflection Yoke and move

the Deflection Yoke as close to the purity magnet as
possible.

4 Adjustment Procedure

4.1. Adjustment Procedure

4.2. COLOUR PURITY

7

TX-29EG20RU-IRAN

Содержание TX-29EG20RU-IRAN
































Отзывы:

Нет отзывов