Panasonic SG-P Series Скачать руководство пользователя страница 51

Страница: 51 / 76

5.2 Daily Inspection

● Before starting work, inspect the following items and verify that there are no

abnormalities. Operating this device without performing the inspection or without
removing the abnormal condition may cause death or serious injury.

■

Checklist (daily inspection)

Check

column

Inspection item

□

The switch body and the actuator are mounted according to the mounting and wiring
specifications and the door and other structures where they are mounted are installed according
to the installation conditions.

□

The door is not deformed or warped.

□

Check each door to confirm that the machine stops when the door opens.

□

There is no change in the installation environment that may affect the results of the risk
assessment performed before this device was installed.

□

If seal was applied to the mounting screw, the seal must remain unchanged.

□

There is no scratch, dirt, or damage in this device.

□

There is no scratch, bent, or damage in the wiring.

5.2 Daily Inspection

WUME-SGPUM-2

5-3

Содержание SG-P Series













































































Результаты поиска

Содержание SG-P Series

Отзывы:

Похожие инструкции для SG-P Series

Бренды по названию

Популярные бренды

Panasonic SG-P Series, Инструкция по эксплуатации

Результаты поиска

Содержание SG-P Series

Отзывы:

Похожие инструкции для SG-P Series

Бренды по названию

Популярные бренды