manualshive.com logo in svg

Panasonic Section 700, Руководство пользователя

Поделиться
Скачать
Panasonic Section 700 Скачать руководство пользователя страница 66

Chapter 3. System Features

Section 700 - Operation

 

Page 3-20

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

DID/DNIS to a Voice Mailbox

(CPC-B Version 6.0 and higher)

Description

DID/DNIS to a voice mailbox allows DID/DNIS calls to be routed to a voice 
mailbox that is not connected to a physical extension. 

To implement this feature, the DID/DNIS trunks must be assigned to ring at 
the voice mail system. Once voice mail answers, the DBS sends a DID/DNIS 
Answer Code required by the voice mail system plus the final DID/DNIS 
digits to the voice mail system. The DID/DNIS Answer Code signals the 
voice mail system to open with a greeting and the DID/DNIS digits specify 
the appropriate mailbox.

Operation

To assign a DID/DNIS Answer Code:

1.  Pick up the receiver or press the ON/OFF key.

2. Press 

PROG

.

3. Dial 

#95

.

4.  Enter the DID/DNIS Answer code required by the voice mail system (1 to 

6 digits).

5. Press 

HOLD

.

6. Press 

the 

ON/OFF

 key.

The 

ON/OFF

 LED goes off.

To display a DID/DNIS Answer Code:

1.  Pick up the receiver or press the ON/OFF key.

2. Press 

CONF

.

3. Dial 

#95

.

4. Press 

the 

ON/OFF

 key.

The 

ON/OFF

 LED goes off.

Содержание Section 700











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды