Panasonic SD XC WV-SFN480 Скачать руководство пользователя | Manualshive

Страница: 180 / 220

background image

Note

•

When the registration for the “Viewnetcam.com” service is completed, the URL registered for
“Personal(Camera) URL” is displayed. It may take up to about 30 minutes until the URL of the registered
camera is validated.

•

To cancel the enrollment in the “Viewnetcam.com” service, access the “Viewnetcam.com” website
(http://www.viewnetcam.com/) later.

•

When “Expired” is displayed in the URL of “Viewnetcam.com” in the viewnetcam settings page or the
status page, restart the camera after registering the “Viewnetcam.com” service. After restarting the
camera, check that the registered URL is displayed in the URL of “Viewnetcam.com” of [Status] -
[Viewnetcam.com] on the “Maintenance” page.

•

It is possible to check the information registered for the “Viewnetcam.com” service by accessing the
URL displayed beside “Your Account Link”. When the URL is not displayed, check that the PC is being
connected to the Internet, and click the [Set] button.

•

If access often fails due to the change in the global address of router, set a smaller value for “Access
interval”.

15.5.4 Checking the information registered for the
“Viewnetcam.com” service

It is possible to check if the camera has been registered for the “Viewnetcam.com” service. (

15.5.5 When using “Dynamic DNS Update”

[Host name]

Enter the host name to be used for the Dynamic DNS Update service.

•

Available number of characters:

3 - 250 characters

Enter in the form of “(host name). (domain name)”.

•

Available characters:

Alphanumeric characters, the colon (:), the period (.), the underscore (_), and the

hyphen (-).

•

Default:

None (blank)

Note

•

Refer to the network administrator for further information about the available host names.

[Access interval]

Select the interval to access the Dynamic DNS Update service server to check the IP address and the host
name from the following.
10min/ 20min/ 30min/ 40min/ 50min/ 1h/ 6h/ 24h

180

Operating Instructions

15 Configuring the network settings [Network]

«
...
178
179
180
181
182
...
»

Содержание SD XC WV-SFN480





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SD XC WV-SFN480

Бренд: Data Harvest Страницы: 19

Concord express

Бренд: GE Страницы: 3

Concord express

Бренд: GE Страницы: 32

Бренд: Tamron Страницы: 2

Бренд: Ecco Страницы: 2

Бренд: Audiotel International Страницы: 16

Бренд: Evolveo Страницы: 83

Бренд: Vicon Страницы: 28

Бренд: WingScapes Страницы: 8

Бренд: HAKO Страницы: 6

Бренд: i3 International Страницы: 3

MAXXUM 2XI - PART 1

Бренд: Minolta Страницы: 24

Бренд: 2gig Technologies Страницы: 4

Бренд: U-Prox Страницы: 2

Бренд: ERS Страницы: 23

Бренд: Yudor Страницы: 91

Бренд: TIP TEMPerature Products Страницы: 7

Бренд: Zamel Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды