Panasonic SC-HG1-C Скачать руководство пользователя страница 67

Страница: 67 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-33

4-9 Error mode

To read the error code of an error that recently occurred, use error mode.

If multiple errors occurred sequentially, only the error code of the last error is read.

Codes can only be read of errors that occurred since the communication unit power was turned

on.

When the communication unit is restarted, the codes of errors that occurred prior to that time

are cleared.

For details on errors, refer to

“<Table of error codes>”

“8-1 Command error”

An example when a master unit and slave units 1 to 3 are connected is shown below.

is only set when the operation mode is CC-Link mode 1.

RY[0E]

Set error code flag

RX[0E]

Check error code flag

RY[10]

Page 1 settings

RX[10]

Check page 1 settings

When operation mode is CC-Link mode 1

RX[7B] (*1)

Check remote ready flag

RWr[00] to [01]

Communication unit error code

RWr[02] to [09]

Check sensor response data

Error code

RWr[02] to [09]

Check sensor response data

Communication unit error code

0x0000

Error code

0x0000

Check that RX[7B]: remote ready flag (*1) is set.

Set the RY[0E]: error code flag. Verify that the RX[0E]: error code flag is set and error mode

has been entered.

The RWr[00] to [01] communication error code is stored. If the operation mode is CC-Link

mode 2 or CC-Link mode 3, the error codes from the controllers are stored in RWr[02] to [09]:

sensor response data.

If the operation mode is CC-Link mode 1, set RY[10]: page 1. Page 1 settings are re-

quested, and RX[10]: page 1 is set. In CC-Link mode 1, always configure the page settings.

The page settings of the sensor response data (master unit, slave units 1 to 14) are as

shown in the table below.

Sensor response data

RY[10]

RY[11]

RY[12]

Master unit, slave units 1 to 6

Slave units 7 to 13

Slave unit 14

If the operation mode is CC-Link mode 1, the error codes from the controllers are stored in

RWr[02] to [09]: sensor response data.

If the operation mode is CC-Link mode 1, clear RY[10]: page 1. Page 1 settings are

cleared, and RX[10]: page 1 is cleared. The error codes of RWr[02] to [09]: sensor re-

sponse data are also cleared.

Clear the RY[0E]: error code flag. The communication unit exits error mode, and the RX[0E]:

error code flag is cleared.

*1: The bit position depends on the operation mode.

CC-Link mode 1: RX[7B], CC-Link mode 2: RX[17B], CC-Link mode 3: RX[1BB]

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 67 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: