Panasonic SC-HG1-C Скачать руководство пользователя страница 3

Страница: 3 / 128

WUME-SCHG1C-4

INTRODUCTION

Thank you for purchasing a CC-Link communication unit

SC-HG1-C

Before using this product, read and understand this User’s Manual. Use the product correctly

and in the optimum manner.

Keep this manual in a safe location for reference whenever necessary.

Types of Manuals

The following user’s manuals are available for the

SC-HG1-C

series. Refer to the appropriate

manual according to your need.

The user’s manuals are also available for download from our website (https://panasonic.net/id/

pidsx/global).

Unit name or purpose of use

Manual name

Manual code

CC-Link communication unit for

digital displacement sensors

SC-HG1-C

User’s Manual

WUME-SCHG1C

Contact-type digital displacement

sensor

HG-S

series

HG-S

User’s Manual

WUME-HGS

Thru-beam type digital displacement

sensor

HG-T

series

HG-T

User’s Manual

WUME-HGT

Please note

1) Unauthorized reproduction of part or all of this manual is prohibited.

2) The contents of this manual are subject to change without notice.

3) This manual has undergone strict quality control procedures; however, in the event that you

discover any problems or points of concern, please contact your local dealer.

4) CC-Link is a registered trademark of Mitsubishi Electric Corporation and is a trademark managed

by CC-Link Partner Association.

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 3 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: