Panasonic SC-HG1-C Скачать руководство пользователя страница 29

Страница: 29 / 128

Installation and Settings

WUME-SCHG1C-4

3-7

3-3-2 Connection

This product must be connected to a controller.
Up to 15 controllers (one master controller and 14 slave controllers) can be connected to the

product.

●

Always shut OFF the power before connecting the product to, or disconnecting the prod-

uct from, a controller. Risk of damage to the product and controller if connected with the

power ON.

● Insert the male connector firmly into the female connector.

●

Risk of damage to the product and controller if not connected completely.

●

To connect the product to a controller, the units must be mounted on a DIN rail. Attach

end plates

MS-DIN-E

(optional) so as to enclose the connected units at the ends.

<Reference>

For detailed information on the digital displacement sensor, refer to the manual of the controller

that you use.

■

Connection procedure

Mount the product on a 35mm width DIN rail.

Remove the connector cover from the controller. (Note 1)

Connector cover

Controller - master (optional)

Controllers - slave (optional)

This product

Note 1: Be sure to keep the connector cover you removed from the controller.

Slide the product until it directly contacts the controller.

Slide

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 29 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: