Panasonic SC-HG1-C Скачать руководство пользователя

Страница: 15 / 128

Before Using This Product

WUME-SCHG1C-4

1-7

1-5 Description of parts

7 6

Name

Function

Station number setting

switch

Set the CC-Link station number to a value from 1 to 64.

(Do not set to 0, or 65 or higher.)

[Factory default state: 1]

Communication speed

setting switch

Set the CC-Link communication speed.

0: 156 kbps, 1: 625 kbps, 2: 2.5 Mbps, 3: 5 Mbps, 4: 10 Mbps

[Factory default state: 156 kbps]

CC-Link connector

Connect to the master station or another slave station.

Male connector

Connect to a master controller or slave controller.

ERR. indicator (Red)

Lights up when CC-Link communication is interrupted. Blinks when a communi-

cation error occurs.

Power indicator (Green) Lights up when power is supplied.

RD indicator (Green)

Lights up during data reception.

L RUN indicator (Green) Lights up during data link execution.

SD indicator (Green)

Lights up during data sending.

L ERR. indicator (Red)

Lights up if the station number setting switch and communication speed setting

switch are in an invalid setting position when the power is turned on.

Blinks if the switch type setting is changed while the power is on.

Mode setting switch

Set the communication method and number of occupied stations.

[Factory default state: CC-Link mode 1]

• CC-Link mode 1

SW No.

ON / OFF ON OFF

Not used (Note)

Remarks CC-Link Ver. 1.10, number of occupied stations: 4

• CC-Link mode 2

SW No.

ON / OFF OFF ON

Not used (Note)

Remarks

CC-Link Ver.2.00, Number of occupied stations: 2

stations

Expanded cyclic transmission speed: x8

• CC-Link mode 3

SW No.

ON / OFF ON

Not used (Note)

Remarks

CC-Link Ver.2.00, Number of occupied stations: 4

stations

Expanded cyclic transmission speed: x4

Note: Always keep unused switches in the OFF position.

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Похожие инструкции для SC-HG1-C

Бренды по названию

Популярные бренды

Panasonic SC-HG1-C, Руководство пользователя

Результаты поиска

Содержание SC-HG1-C

Отзывы:

Похожие инструкции для SC-HG1-C

Бренды по названию

Популярные бренды