Panasonic SC-HG1-C Скачать руководство пользователя

Страница: 13 / 128

Before Using This Product

WUME-SCHG1C-4

1-5

1-3 Glossary

Term

Meaning

System

terms

Transient transmission

A function in Data Link for communication with other stations using

peripheral devices, including reading or writing data from / to another

station by means of a read / write command in the program of the local

station.

Cyclic transmission

A function in Data Link for periodic data communication between stations

on the same network.

Memory map

This assigns functions of a communication unit to a link device. By ac-

cessing a link device that supports memory map, the master station can

use the functions of a communication unit.

Station number

This number is assigned to identify each network unit connected to a

network.

The same number cannot be assigned to more than one network unit in a

network.

RX[*]

Remote input

Information input from a slave station to the master station in units of

bits.

[*]: Indicates the bit number in hex.

RY[*]

Remote output

Information output from the master station to a slave station in units of

bits.

[*]: Indicates the bit number in hex.

RWw[*]

Remote register (output)

Information output from the master station to a slave station in units of

words (16 bits).

[*]: Indicates the word number in hex.

RWr[*]

Remote register (input)

Information input from a slave station to the master station in units of words

(16 bits).

[*]: Indicates the word number in hex.

Unit name

Master station

This station controls the overall network. The master station can com-

municate with all stations by cyclic transmission and transient transmis-

sion.

Slave station

A general name for stations other than the master station (local station,

remote I/O station, remote device station, intelligent device station).

Remote I/O station

Exchanges input / output signals in units of bits with the master station by

cyclic transmission.

Remote device station

Sends information in units of bits and information in units of words by

cyclic transmission. Returns a response to a transient transmission from

another station.

Intelligent device sta-

tion

Sends input / output signals in units of bits and input / output data in

units of words to the master station by cyclic transmission. Returns a re-

sponse to a transient transmission (request) from another station.

Local station

Communicates with the master station and other local stations by cyclic

transmission and transient transmission.

Controller - Master unit A controller equipped with power supply, external I/O, and analog cur-

rent output wires, and which can be used on a standalone basis.

Controller - Slave unit

A controller that is connected to a master unit.

CC-Link dedicated

cable

Cable certified by CC-Link Partner Association (shielded 3-conductor

twisted-pair cable).

End plates or commer-

cially available fittings

When the product is connected to a controller, the end plates secure

the units at both ends to prevent the connector from disconnecting and

causing a communication failure.

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Похожие инструкции для SC-HG1-C

Бренды по названию

Популярные бренды

Panasonic SC-HG1-C, Руководство пользователя

Результаты поиска

Содержание SC-HG1-C

Отзывы:

Похожие инструкции для SC-HG1-C

Бренды по названию

Популярные бренды