Panasonic SC-HG1-C Скачать руководство пользователя страница 122

Страница: 122 / 128

Troubleshooting

WUME-SCHG1C-4

8-6

8-3 Description of indicators

You can check the indicators on the product to identify the cause of a problem and take correc-

tive action.

1 2 3

Name

Function

L ERR. indicator (Red)

Lights up if the station number setting switch and communication speed setting

switch are in an invalid setting position when the power is turned on.

Blinks if the switch type setting is changed while the power is on.

SD indicator (Green)

Lights up during data sending.

ERR. indicator (Red)

Lights up when CC-Link communication is interrupted. Blinks when an error occurs

in communication between controllers.

Power indicator

(Green)

Lights up when power is supplied.

RD indicator (Green)

Lights up during data reception.

L RUN indicator

(Green)

Lights up during data link execution.

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 122 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: