
13 Parts Location and Replacement Parts List
Notes:
●
Important safety notice:
Components identified by
mark have special characteristics important for safety.
Furthermore, special parts which have purposes of fire-retardent (resistors), high-quality
sound (capacitors), low noise (resistors), etc are used.
When replacing any of these components, be sure to use only manufacturer’s specified parts
shown in the parts list.
●
The parenthesized indications in the Remarks columns specify the areas or colour. (Refer to
the cover page for area or colour)
Parts without these indications can be used for all areas.
●
Capacitor values are in microfarads (
μ
F) unless specified otherwise, P= Pico-farads (pF), F=
Farads.
●
Resistance values are in ohms, unless specified otherwise, 1K=1,000 (OHM).
●
The marking (RTL) indicates that the Retention Time is limited for this items. After the
discontinuation of this assembly in production, the item will continue to be available for a
specific period of time. The retention period of a availabilityis dependent on the type of
assembly, and in accordance with the laws governing part and product retention. After the end
of this period, the assembly will no longer be available.
●
[M] Markings in the Remarks columns indicates parts supplied by
PAVCSG.
Содержание SB-WA520EB
