Panasonic PT-RZ16K, Руководство по эксплуатации

Страница: 173 / 270

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 173
[DETAILED INFORMATION]
[INPUT] Displays the input terminal used for the projected image.
[SIGNAL FORMAT] Displays the format of the input signal.
[SIGNAL FREQUENCY] Displays the frequency of the input signal.
[SCAN TYPE] Displays the scan type of the input signal.
[TOTAL DOTS]
Displays the total dot count of the input signal.
[DISPLAY DOTS] Displays the number of input signal display dots.
[TOTAL LINES] Displays the total line count of the input signal.
[DISPLAY LINES] Displays the number of input signal display lines.
[COLOR FORMAT] Displays the color format of the input signal.
[SAMPLING]
Displays the sampling information of the input signal.
[BIT DEPTH] Displays the gradation of the input signal.
[SIGNAL LEVEL] Displays the signal level of the input signal.
[HDCP STATUS]
Displays the HDCP status of the input signal. The content of display
is as follows.
[PROTECTED]: When protected with HDCP
[NONE]: When not protected with HDCP
[―]: When there is no signal
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is
green.
*2 This is displayed only when the standard DC motor unit installed in the Zoom Lens (Model No.: ET‑D75LE6, ET‑D75LE8, ET‑D75LE10,
ET‑D75LE20, ET‑D75LE30, ET‑D75LE40, etc.) is replaced with the stepping motor unit using the Stepping Motor Kit (Model No.:
ET-D75MKS10), or when a projection lens with the stepping motor is attached.
*3 [CONSOLIDATED RUNTIME] can be obtained with the following calculation formula. Values obtained by the calculation formula contain a
slight error.
Conversion formula for [CONSOLIDATED RUNTIME]
A
x 1.0 +
B
x 0.8
f
A
: Runtime of the light source with [OPERATING MODE] set to [NORMAL], [USER1], [USER2], or [USER3]
f
B
: Runtime of the light source with [OPERATING MODE] set to [ECO]
Note
f
The content of the status can be sent to the E‑mail address (up to two addresses) set in “[E‑mail set up] page” (
x
page 210) when the
<ENTER> button is pressed while displaying the pages 1/6 to 5/6 of the [STATUS] screen.
f
The detailed information of the input signal is displayed when the <ENTER> button is pressed while displaying the page 6/6 of the
[STATUS] screen. Information for multiple input signals may be displayed depending on the projected image. Press
qw
to switch pages.
f
There are items that are displayed or not displayed in [SIGNAL INFORMATION] and [DETAILED INFORMATION] depending on the setting
or the input signal.
f
If any abnormality has occurred on the projector, press the <DEFAULT> button while the [STATUS] screen is displayed to display the detail
screen of the error information.
f
For details on the contents displayed in [SELF TEST], refer to “Self‑diagnosis display” (
x
page 231).
[AC VOLTAGE MONITOR]
Enable or disable the AC voltage monitor function. The value of input supply voltage is displayed on the self-
diagnosis display at the side of the projector when enabled.
1) Press
as
to select [AC VOLTAGE MONITOR].
2) Press
qw
to switch the item.
f
The items will switch each time you press the button.
[OFF]
Disables the AC voltage monitor function.
[ON] Enables the AC voltage monitor function.
Note
f
When [ON] is set, the value of the input supply voltage is always displayed in the self-diagnosis display while the main power of the projector
is turned on.
f
Even when [OFF] is set, the value of input supply voltage can be displayed temporarily in the self-diagnosis display by operating the button
on the remote control. (
x
page 84)
f
The value of input supply voltage cannot be displayed in the self-diagnosis display during standby when the [PROJECTOR SETUP] menu
→ [STANDBY MODE] (
x
page 163) is set to [ECO].
[SAVE ALL USER DATA]
Save the various setting values as a backup in the built-in memory of the projector.
1) Press
as
to select [SAVE ALL USER DATA].