background image

Powering ON/OFF

ENGLISH - 

27

Basic Operation

ON(G)/STANDBY(R) indicator

The ON(G)/STANDBY(R) indicator informs you the status of the power. Confirm the status of the 

 

<ON(G)/STANDBY(R)> indicator before operating the projector.

<ON(G)/STANDBY(R)> indicator 

Indicator status

Status

No illumination or blinking

The power plug is not connected to the outlet.

Red

Lit

1

The power is switched off. (Standby mode)

Press <

v

/

b

> to start projection.

Slow

 

Blinking

2

The power is switched off. (Standby mode)

Press <

v

/

b

> to start projection.

Blinking

The projector is preparing to switch off the power.

The power is switched off after a while. (Changes to the standby mode.)

Green

Lit

The projector is in the projection status.

Blinking

The projector is preparing for projection.

1 When [VGA Out (Standby)]/[In Standby Mode (Audio)] are all set to [Off].

2  When one or more among [VGA Out (Standby)]/[In Standby Mode (Audio)] is/are set to [On].

Note

When the <ON(G)/STANDBY(R)> indicator is blinking in red, the internal fans start to operate and the projector starts 

 

z

cooling.

Содержание PT-LX270U































































Отзывы: