Panasonic NA-126MB1WSA Скачать руководство пользователя страница 18

Страница: 18 / 62

6. MALFUNCTION CODES AND EXPLANATIONS

Malfunction

code

Reason

Possible cause

Solution

E10

n 3 minutes,

the water level

doesn’t

change with

valves open

The water level

doesn’t changed in 3

minutes during filling

the water.

If the washer fills very slowly, the

water pressure from the house

might be too low. If the water inlet

valve isn't leaking and there are

no other symptoms this problem

does not need to be corrected.

Water inlet hose

Make sure that water faucet is

turned on and that the screens on

the hoses are not restricted.

Water inlet

valve

(The voltage on

the water inlet

valve is normal)

If the water pressure is good, try

cleaning the screens inside the

water inlet valve hose connection

ports. If those are clean replace

the water inlet valve.

Water level

sensor or

control switch

(No voltage on

the water inlet

valve)

A water lever control switch

controls how much water enters

the washing machine by PCB. If

the water level control switch is

defective, or more commonly, if

the small air pipe attached to the

air bell restricted, The switch will

not be able to close the electrical

contacts to the washer fill valve.

CHECK THE AIR PIPE

CHECK THE WATER LEVERL

SENSOR

CHECK THE PCB and the inner

wire between PCB and the sensor

E12

The water

level in drum

exceed a

certain level

for alarm

Restart

Sometimes just restart the unit
can solve the problem.

Water inlet valve

(The voltage on the

water inlet valve is

normal)

If the washer is overflowing, the

water inlet valve has failed.

Replace it.

Water level

sensor or

control switch

(No voltage on

the water inlet

valve)

A water lever control switch

controls how much water enters

the washing machine by PCB. If

the water level control switch is

defective, or more commonly, if

the small air pipe attached to the

air bell restricted, The switch will

not be able to close the electrical

contacts to the washer fill valve.

CHECK THE AIR PIPE

CHECK THE WATER LEVERL

SENSOR

CHECK THE PCB and the inner

wire between PCB and the sensor

Содержание NA-126MB1WSA































































Результаты поиска

Содержание NA-126MB1WSA

Отзывы:

Похожие инструкции для NA-126MB1WSA

Бренды по названию

Популярные бренды

Panasonic NA-126MB1WSA, Руководство по обслуживанию

Результаты поиска

Содержание NA-126MB1WSA

Отзывы:

Похожие инструкции для NA-126MB1WSA

Бренды по названию

Популярные бренды