Panasonic LX-TD500 Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 388

background image

System

124

Programming Guide

2.7

Trunk to Trunk Restriction

Used to allow or restrict the trunk-to-trunk relay function (routing a trunk call from one Trunk
Group to another) on a trunk group basis.
Please refer to "TIE Line Network – Alternate Routing" of Section "3.1 TIE Line Features" in
the Features Guide for further information.

Parameter

Source Trunk Group No.

Default

1

Value Range

1-48

Description/Function

Specifies the source trunk group (1-48), the first point of trunk-to-
trunk relay, which you are going to program.

Reference

• 3.1 TIE Line Features (F/G)

– TIE Line Service

Parameter

Destination Trunk Group No. (1-48)

Default

No check

Value Range

1.

No check [Restricted]

2.

Check [Not restricted]

Description/Function

Specifies the destination trunk group (1-48), the second point of
trunk-to-trunk relay, which you allow to accept a trunk call from the
source trunk group.

Reference

• 3.1 TIE Line Features (F/G)

– TIE Line Service

«
...
122
123
124
125
126
...
»

Содержание LX-TD500





































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LX-TD500

Бренд: Bajaj Motorsport Страницы: 8

Бренд: Razor Страницы: 2

Бренд: Ezgo Страницы: 64

1995 Fourtrax 300

Бренд: Honda Страницы: 156

JACOBSEN 4800 2006+

Бренд: E-Z-GO Страницы: 114

Бренд: UtilityDump Страницы: 13

Бренд: Buffalo Tools Страницы: 2

Sniper T-1500 2S

Бренд: BMS Страницы: 69

Honey Joy TY324116

Бренд: Costway Страницы: 7

Sportsman 850 Touring EPS

Бренд: Polaris Страницы: 510

Бренд: E-Z-GO Страницы: 204

VIPER 50 ST - SERVICE

Бренд: E-TON Страницы: 68

Бренд: Baja Страницы: 82

Бренд: Yamaha Страницы: 184

Expediter EX-21 2017

Бренд: Columbia Страницы: 32

BR-150 Bug Rider

Бренд: PGO Страницы: 72

Bug Rider BR-250

Бренд: PGO Страницы: 121

Бренд: ATV Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды