Panasonic Lumix DC-FT7EB Скачать руководство пользователя | Manualshive

Страница: 7 / 45

background image

7

3.5.

General Description About Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the
normal solder.

Distinction of P.C.B. Lead Free Solder being used

Service caution for repair work using Lead Free Solder (PbF)

• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.

(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)

• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the

lead free solder.

• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C

(662±86°F).

Recommended Lead Free Solder (Service Parts Route.)

• The following 3 types of lead free solder are available through the service parts route.

SVKZ000001-----------(0.3mm 100g Reel)
SVKZ000002-----------(0.6mm 100g Reel)
SVKZ000003-----------(1.0mm 100g Reel)

Note

* Ingredient: Tin (Sn) 96.5%, Silver (Ag) 3.0%, Copper (Cu) 0.5%. (Flux cored)

«
...
5
6
7
8
9
...
»

Содержание Lumix DC-FT7EB














































Отзывы:

Нет отзывов

Похожие инструкции для Lumix DC-FT7EB

Бренд: Canon Страницы: 3

CAMEDIA SP-500 UZ

Бренд: Olympus Страницы: 189

Бренд: Olympus Страницы: 220

Бренд: Ubiquiti Страницы: 24

Бренд: Intova Страницы: 2

Бренд: Commax Страницы: 8

FREEDOM ZOOM 130

Бренд: Minolta Страницы: 33

Бренд: Casio Страницы: 91

Бренд: Intova Страницы: 2

Бренд: Optika Italy Страницы: 72

Бренд: Netum Страницы: 6

Бренд: ViewSonic Страницы: 4

Бренд: Xview Страницы: 16

Бренд: Aluratek Страницы: 24

Бренд: Onvif Страницы: 14

Бренд: Dignsys Страницы: 66

Бренд: Edimax Страницы: 77

100mm F2.8 ED UMC MACRO

Бренд: Samyang OPTICS Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды