Panasonic LP-M Series Скачать руководство пользователя

Страница: 63 / 174

2-4-5 When using monitor and mouse

• Be sure to check the operation status when using the monitor and mouse beforehand. This connection status does not

warrant all operations of VGA monitor and USB mouse.

• Do not take out and put in a monitor, and a mouse in being powered on.

• When using monitor and mouse, do not connect the return harness.

• USB hub cannot be used for this product.

• There is 1 port on the front of the controller and 2 ports on the back for USB connector A. USB mouse can be connected

in any of these ports.

No.

Description

Monitor: VGA terminal (15-pin 3-row) (Recommended pixel count: 640×480 or more)

Mouse: USB mouse with Human interface device (HID) class

Rear side of controller

To VGA OUT connector

To USB connector A

ME-LPM-SSM-10

Содержание LP-M Series















































































































































































Результаты поиска

Содержание LP-M Series

Отзывы:

Похожие инструкции для LP-M Series

Бренды по названию

Популярные бренды

Panasonic LP-M Series, Руководство по обслуживанию

Результаты поиска

Содержание LP-M Series

Отзывы:

Похожие инструкции для LP-M Series

Бренды по названию

Популярные бренды