Panasonic LP-M Series Скачать руководство пользователя

Страница: 11 / 174

How to Read this Document

Symbol indications

ワㄐㄕㄊ㄄ㄆ

“Notice” denotes any instructions or precautions for using this product. To prevent the damage or

malfunction of the product, observe these precautions fully.

ンㄆㄇㄆㄓㄆㄏ㄄ㄆ

“Reference” denotes any hints for operation, detail explanations, or references.

Type of manuals

For this product, the following manuals are prepared. Read each manuals and operate this product correctly and safely.

Save the manuals for future use.

Safety / Setup / Maintenance Guide

This manual describes the safety precautions and the items required for the introduction, installation and maintenance of

this product.

• Precautions and safety measures: All users shall be required for reading this part.

• Specifications and outer dimensions

• Setup and connecting method

• I/O control method (signal layout, I/O rating, timing chart etc.)

• Maintenance

• Troubleshooting

Operation Manual

This manual describes how to operate the laser marker and set the marking data using touch panel console or monitor

and mouse.

Laser Marker NAVI plus Operation Manual

This manual describes how to operate the laser marker and set the marking data using PC setting software “Laser

Marker NAVI plus”.

Serial Communication Guide

This manual describes the communication commands to control this product externally using the serial communication

(RS-232C/Ethernet). It describes the communication conditions, communication data formats, communication

commands, and the control samples.

Mainly the machine builder and system integrator shall be required for reading this manual.

ンㄆㄇㄆㄓㄆㄏ㄄ㄆ

• The PDF data of each manual is included on an attached CD-ROM “Laser Marker Utility”.

• To read the PDF manual, Adobe Reader (Version X or later) of Adobe Systems Incorporated is required.

ME-LPM-SSM-10

Содержание LP-M Series















































































































































































Результаты поиска

Содержание LP-M Series

Отзывы:

Похожие инструкции для LP-M Series

Бренды по названию

Популярные бренды

Panasonic LP-M Series, Руководство по обслуживанию

Результаты поиска

Содержание LP-M Series

Отзывы:

Похожие инструкции для LP-M Series

Бренды по названию

Популярные бренды