Panasonic LP-GS Series Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 190

background image

69

4-1 I/O Interface Specification

The I/O terminal block and the I/O connector are available as the external control I/O interface of this product.

• I/O terminal block: Loaded with the basic input/output to control the laser marker.
• I/O connector: Loaded with the input/output for data configuration such as selecting a file number and the input/output

for the specific functions.

ンㄆㄇㄆㄓㄆㄏ㄄ㄆ

• Before using I/O, configure the system settings. Refer to “3-4-3 Settings before external control” (P.64).

X1

X2

X3

X4

X5

X6

X7

X8

X9

X10

X11

X12

X13

X14

X15

X16

X17

X18

X19

X20

Y1

Y2

Y3

Y4

Y5

Y6

Y7

Y8

Y9

Y10

Y11

Y12

Y13

Y14

Y15

Y16

Y17

Y18

Y19

Y20

39

1

2

40

Rear of controller

I/O terminal block

I/O connector

(Laser marker)

Hook

The I/O terminal block can be
removed by holding down the
hooks.

Connector specifications and models

Connector position

Connector specifications

Model

Manufacturer name

I/O terminal
block

On the laser
marker side

Dedicated connector

DMC1.5/20-GIF-3.5-LR
P20THR

Phoenix Contact
Company

User side

Accessories: DFMC1.5/20-ST-
3.5-LR

I/O Connector On the laser

marker side

MIL connector
40-pin/male

XG4A-4034

OMRON Corporation

User side

MIL connector
40-pin/female

Recommended item: XG4M-
4030-T

Wiring the shielded line

If you use a shielded wire for the I/O terminal block and the I/O connector cable, you can use the frame ground terminal on
the rear of the controller as the frame earth of the shielded wire.

Rear of controller

Shielded wire

Frame ground terminal

ME-LPGS-SM-8

«
...
67
68
69
70
71
...
»

Содержание LP-GS Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LP-GS Series

Бренд: FJC Страницы: 2

Бренд: Samsung Страницы: 2

Crouse-hinds series

Бренд: Eaton Страницы: 32

COOPER POWER SERIES

Бренд: Eaton Страницы: 8

Бренд: IBEX Страницы: 4

Бренд: Xycom Страницы: 65

Бренд: Xtool Страницы: 8

bionic power knee

Бренд: Össur Страницы: 2

BALANCE KNEE OM8

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 37

REBOUND DIABETIC WALKER

Бренд: Össur Страницы: 63

Бренд: Össur Страницы: 67

ECHODIA Babyscreen

Бренд: Électronique du Mazet Страницы: 65

Бренд: Orliman Страницы: 11

BOMAG BVP 12/50 A

Бренд: Fayat Страницы: 105

HALO miniLUME LA5300

Бренд: Cooper Lighting Страницы: 2

Бренд: Free The Tone Страницы: 8

Бренд: Perel Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды