Panasonic LP-GS Series Скачать руководство пользователя страница 26

Страница: 26 / 190

1-5-3 Cables

Unit power cable

Unit: mm
Minimum bent radius 100mm
Flex-resistant cable

5000

+200

Signal cable

Unit: mm
Minimum bent radius 100mm
Flex-resistant cable

5000

+200

AC power cable

Attached AC power cable varies depending on each model. Select a cable suitable for the standards in the country or
region where it is used.

Rating 125V, PSE standards and CSA/UL standards compatible cable (North America, Japan): Included in LP-GS051(-

L/-F/-LF)/LP-GS052(-F)

Rating 250V, VDE standards compatible cable (Europe): Included in LP-GS051-(L/F/LF)E / LP-GS052-(F)E

Rating 250V, CCC standards compatible cable (China): Included in LP-GS051-(L)FN / LP-GS052-FN

Unit: mm
Minimum bent radius 50mm

3000±100

ワㄐㄕㄊ㄄ㄆ

• Be sure to connect the ground pin of the AC power cable to earth permanently.

ンㄆㄇㄆㄓㄆㄏ㄄ㄆ

• AC power cable with Rating 250V approved PES standard is available as option items (LP-ACA11). For details, please

contact our sales office.

ME-LPGS-SM-8

Содержание LP-GS Series































































































































































































Результаты поиска

Содержание LP-GS Series

Отзывы:

Похожие инструкции для LP-GS Series

Бренды по названию

Популярные бренды

Panasonic LP-GS Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание LP-GS Series

Отзывы:

Похожие инструкции для LP-GS Series

Бренды по названию

Популярные бренды