Panasonic KX-UTG200 Скачать руководство пользователя страница 104

Страница: 104 / 412

LLDP-MED Interval Timer (5-3600s)

Description

Specifies the interval, in seconds, between sending each LLDP frame.

Value Range

5–3600

Default Value

Configuration File Reference

LLDP_INTERVAL (Page 275)

4.3.4.3 CDP Settings

Enable CDP

Description

Selects whether to enable or disable sending and receiving CDP
frames.

Note

•

You should specify "

Yes

" for only one of "

VLAN

", "

LLDP

" or

CDP

•

If "

Yes

" is specified for two or more of the parameters above,

the settings are prioritized as follows: "

VLAN

" > "

LLDP

" >

CDP

". Therefore, if "

Yes

" is specified for both "

VLAN

" and

CDP

", the VLAN-related settings are used.

Value Range

•

Yes

•

Default Value

Yes

Configuration File Reference

CDP_ENABLE (Page 276)

CDP Interval Timer

Description

Specifies the time between CDP messages.

Value Range

5–3600

Default Value

Configuration File Reference

CDP_INTERVAL (Page 276)

104

Administrator Guide

Document Version 2015-01

4.3.4 Ethernet Port Settings

Содержание KX-UTG200





























































































































































































































































































































































































































Результаты поиска

Содержание KX-UTG200

Отзывы:

Panasonic KX-UTG200, Руководство по установке, Страница: 104 / 412

Результаты поиска

Содержание KX-UTG200

Отзывы: