background image

Default Value

STUN

Detection Interval

Description

Specifies the interval, in seconds, to wait between attempts to detect
the global IP address.

Value Range

0, 10–65535 (0: Disable)

Note

When 

[Detection Method]

 is set to 

[SIP]

, the value "0" disables

detection and a value other than "0" enables detection.

Default Value

0

4.4.4.2  STUN Server

STUN Server Address

Description

Specifies the IP address or FQDN of the STUN server.

Value Range

Max. 127 characters

Default Value

Not stored.

Configuration File Reference

STUN_SERV_ADDR (Page 157)

STUN Server Port

Description

Specifies the port number of the STUN server.

Value Range

1–65535

Default Value

3478

Configuration File Reference

STUN_SERV_PORT (Page 158)

4.4.5  Static NAPT Settings

This screen allows you to configure the NAPT (Network Address Port Translation) settings. If the unit is
connected behind a router that uses NAT/NAPT to translate between private and global IP addresses, VoIP

80

Administrator Guide

Document Version  2012-07  

Section 4 Web User Interface Programming

Содержание KX-UT670



























































































































































































































































Отзывы: