Panasonic KX-UT670 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 250

background image

Value Range

Max. 15 characters

Default Value

Not stored.

Phone User Interface
Reference

Network Settings (Page 16)

4.4.2 Ethernet Port Settings

This screen allows you to change the connection mode of the Ethernet ports, the LLDP settings and the VLAN
settings.

Note

•

When you change the settings on this screen and click

[Save]

, the message "Complete" is displayed,

and then the unit will restart automatically even if the unit is on a call.

•

Incorrect settings may cause a network failure. In such a case, you cannot access the Web user
interface anymore. To access it again, you need to correct the speed/duplex settings or perform IP
Reset through phone user interface programming. For details, refer to the Operating Instructions on
the Panasonic Web site (

®

see

Introduction

).

4.4.2.1 Link Speed/Duplex Mode

LAN Port

Description

Selects the connection mode (link speed and duplex mode) of the LAN
port.

Document Version 2012-07

Administrator Guide

73

Section 4 Web User Interface Programming

«
...
71
72
73
74
75
...
»

Содержание KX-UT670



























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-UT670

Бренд: NEC Страницы: 19

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 2

Бренд: Warner Telecom Group Страницы: 6

Бренд: Samsung Страницы: 252

Galaxy S20 FE 5G

Бренд: Samsung Страницы: 19

Galaxy S Epic SPH-D700

Бренд: Samsung Страницы: 264

Galaxy S II Skyrocket SGH-i727

Бренд: Samsung Страницы: 206

Galaxy S Plus GT-I9001

Бренд: Samsung Страницы: 147

Бренд: Samsung Страницы: 48

Galaxy J7 Prime

Бренд: Samsung Страницы: 33

Бренд: Samsung Страницы: 32

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 11

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 65

Бренд: Samsung Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды