Panasonic KX-UT670 Скачать руководство пользователя

Страница: 115 / 250

Busy (Phone Number)

Description

Specifies the phone number of the destination to forward calls to when
the line is in use.

Note

•

If you change this setting when

[Synchronize Do Not Disturb

and Call Forward]

is set to

[Yes]

, the change to this setting is

not immediately applied on this screen. In this case, reload the
screen to confirm that the change is applied.

Value Range

Max. 32 characters

Note

•

You cannot leave this field empty if

[Busy (Enable Call

Forward)]

is set to

[Yes]

Default Value

Not stored.

No Answer (Enable Call Forward)

Description

Selects whether to forward incoming calls to a specified destination
when a call is not answered after it has rung a specified number of
times.

Note

•

If Do Not Disturb has been enabled on the server, the server
rejects incoming calls and the unit does not receive any calls,
even if you have selected

[Yes]

for this setting.

•

If you have selected

[Yes]

for this setting and Call Forward has

been enabled on the server, but the forwarding destinations
differ, incoming calls are forwarded to the destination set on the
server.

•

If Call Forward has been enabled on the server, incoming calls
are forwarded to the destination set on the server, even if you
have selected

[No]

for this setting.

•

You can synchronize the Do Not Disturb and Call Forward
settings from the Web user interface (

see

[Synchronize Do

Not Disturb and Call Forward]

4.7.2.1 Call Control

) or

through configuration file programming (

see

FWD_DND_SYNCHRO_ENABLE_n

" in

5.8.1 Call Control

Settings

•

If you change this setting when

[Synchronize Do Not Disturb

and Call Forward]

is set to

[Yes]

, the change to this setting is

not immediately applied on this screen. In this case, reload the
screen to confirm that the change is applied.

Value Range

•

Yes

•

Default Value

Document Version 2012-07

Administrator Guide

115

Section 4 Web User Interface Programming

Содержание KX-UT670



























































































































































































































































Результаты поиска

Содержание KX-UT670

Отзывы:

Похожие инструкции для KX-UT670

Бренды по названию

Популярные бренды

Panasonic KX-UT670, Руководство администратора

Результаты поиска

Содержание KX-UT670

Отзывы:

Похожие инструкции для KX-UT670

Бренды по названию

Популярные бренды