manualshive.com logo in svg

Panasonic KX-TVM50, Руководство по установке

Поделиться
Скачать
Panasonic KX-TVM50 Скачать руководство пользователя страница 72

2.14  Initialising the VPS During Installation

Before programming the VPS for the first time, perform the initialisation procedure described below. All settings
are reset to their default values. 

Recorded messages are erased.

 System prompts (including customised

prompts) are preserved.

1.

Turn the power switch to the off position.

2.

Set the Mode Switch to position 5 (see 2.3  Names and Locations).

3.

Turn the power switch to the on position.

4.

Confirm that the 

RUN

 indicator blinks 5 times.

•

This may take several minutes. The 

ALARM

 indicator and 

RUN

 indicator will first blink intermittently

before the 

RUN

 indicator blinks 5 times.

5.

Turn the power switch off at the VPS.

6.

Set the Mode Switch to position 0.

7.

Turn the power switch back on at the VPS.

After initialising the VPS, continue with the installation procedure and/or begin programming the VPS.

72

Installation Manual

Document Version  2.1  2008/04

2.14 Initialising the VPS During Installation

Содержание KX-TVM50









































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды