manualshive.com logo in svg

Panasonic KX-TVM200, Руководство по установке

Поделиться
Скачать
Panasonic KX-TVM200 Скачать руководство пользователя страница 161

5.3 KX-TDA Series PBX Programming for Inband Integration

Installation Manual

161

5.3

KX-TDA Series PBX Programming for Inband 
Integration

DPT Integration is recommended when using the VPS with a KX-TDA series PBX, however, Inband 
Integration is necessary when the PBX has available SLT ports but no available DPT ports.

The screen shots shown in this section are for the KX-TDA200. Programming procedures and 
availability may vary by country/area, software version, etc. Refer to the documentation 
included with the PBX or consult your dealer for more information.

1.

Assignment of VM (DTMF) Group

a)

Go

 to the 

"Groups-VM(DTMF) Group-Group Setting"

 screen.

b)

Assign

 a floating extension number to the desired VM (DTMF) group.

c)

Select

 AA as the service type.

d)

Assign

 extension numbers to 

"Extension Number of the SLT Port connected to VM"

. 

Incoming calls will hunt starting at the lowest VM Port number.

e)

Click "Apply"

 to save the changed data.

Содержание KX-TVM200



























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды