Link to cell settings
Selecting which unit receives cellular
calls
You can select which unit rings and receives calls
for a cellular line. When
“
All
”
is selected, all
handsets and the base unit ring.
You can configure this setting using either the
base unit or one of the handsets.
Handset / Base unit
1
For CELL 1:
M
MENU
N#6271
For CELL 2:
M
MENU
N#6272
2
MbN
: Select the desired handset or
“
All
”
.
a
M
SAVE
N
3
Proceed with the operation for your unit.
Handset:
M
OFF
N
Base unit:
M
EXIT
N
Note:
R
When you select a specific handset to receive
calls for a cellular line:
– other handsets cannot answer the calls.
– the base unit can answer the calls even
though it does not ring. However, you can
make the base unit ring by adjusting the base
unit ringer volume (page 39).
R
When you change to
“
All
”
from another
setting, the base unit ringer volume also returns
to the lowest level even if the ringer volume was
changed.
R
The units selected with this setting have the
alert feature (page 54) applied to them.
Ring as cell mode
Once this feature is turned on, the handset and
base unit ring using the same ringer tone as your
cellular phone.
The following settings are available:
–
“
Off
”
: Turn this feature off to use the ringer
tones of the handset and base unit. Caller
information is announced depending on the
Talking Caller ID setting (page 41).
–
“
On (with Talking CID)
”
(default): The
handset and base unit use your cellular phone’s
ringer tone. Caller information is announced
even if the Talking Caller ID is turned off.
–
“
On (without Talking CID)
”
: The
handset and base unit use your cellular phone’s
ringer tone. Caller information is not announced
even if the Talking Caller ID is turned on.
You can configure this setting using either the
base unit or one of the handsets.
Important:
R
To use this feature, your cellular phone must
support Bluetooth in-band ringtone. Refer to
your cellular phone’s operating instructions.
Handset / Base unit
1
For CELL 1:
M
MENU
N#6141
For CELL 2:
M
MENU
N#6142
2
MbN
: Select the desired setting.
a
M
SAVE
N
3
Proceed with the operation for your unit.
Handset:
M
OFF
N
Base unit:
M
EXIT
N
Note:
R
The units use the preset ringer tones instead of
your cellular phone’s ringer tone when a cellular
call is being received if:
– your cellular phone is in night mode
(depending on your cellular phone).
– the base unit is in use.
– 2 handsets are sharing a landline call.
R
If your cellular phone is in night mode with
“
On
(with Talking CID)
”
set, the unit
announces caller information even when Talking
Caller ID is turned off (page 41).
To use the handset ringer tone instead of your
cellular phone’s ringer tone
Select
“
Off
”
in step 2, “Ring as cell mode”,
page 17.
To change the handset ringer tone for a cellular
line, see page 39.
Auto connection to the Bluetooth
devices (cellular phones)
After pairing, your Bluetooth devices are
connected to the base unit. If you move the
Bluetooth devices out of base unit range, the
Bluetooth devices are disconnected from the base
unit. This feature allows the base unit to try to
reconnect the Bluetooth devices at regular
intervals when it returns within base unit range.
You can set the interval. The default setting is
“
1
min
”
.
You can configure this setting using either the
base unit or one of the handsets.
For assistance, visit www.panasonic.ca/english/support
17
Link to Cell
TG153CSK(en)_0422_ver021.pdf 17
2016/04/22 14:54:41
