Panasonic KX-TDE200 Скачать руководство пользователя страница 170

Страница: 170 / 204

3.13 Starting the PBX

3.13.1 Starting the PBX

Before Starting the PBX

Before starting the PBX, please pay attention to the following:

Notice

The SD Memory Card must be inserted in the SD Memory Card slot of the IPCMPR card before startup.

Starting the PBX

WARNING

Use only the AC power cord included with the PBX for the PSU.

CAUTION

•

Before touching the System Initialise Switch, discharge static electricity by touching ground or wearing
an earthing strap.

•

Once you have started the PBX and if you unplug the PBX, do not perform the following procedures
to start the PBX again. Otherwise, your programmed data is cleared. To restart the PBX, refer
to "5.1.4 Using the Reset Button".

•

The power supply cord is used as the main disconnect device. Ensure that the AC outlet is located
near the equipment and is easily accessible.

Note

The PBX will continue to be powered even if the power switch is turned "OFF".

System Initialisation Procedure

Slide the System Initialise Switch to the "SYSTEM INITIALIZE" position.

RESET

SYSTEM

INITIALIZE

NORMAL

RUN Indicator

Reset Button

System Initialise Switch

170

Installation Manual

3.13.1 Starting the PBX

Содержание KX-TDE200













































































































































































































Результаты поиска

Содержание KX-TDE200

Отзывы:

Похожие инструкции для KX-TDE200

Бренды по названию

Популярные бренды

Panasonic KX-TDE200, Руководство по установке

Результаты поиска

Содержание KX-TDE200

Отзывы:

Похожие инструкции для KX-TDE200

Бренды по названию

Популярные бренды