Panasonic KX-TD500CE Скачать руководство пользователя страница 114

Страница: 114 / 376

1.5

Attended Features

114

Features Guide

Direct In Lines (DIL)

Description

Enables an incoming CO call to go directly to one or more answering points without assistance
of the operator.

DIL 1:1 puts an incoming CO call to a single destination. Assignable destinations are:

(1) Extension

(2) Floating Extension

— Modem (Remote Administration)

— External Pager (TAFAS)

— OGM Group (DISA message)

— Extension Group

— DIL 1:N Group

— Phantom Extension

This CO line can be used by multiple extension users to make calls but can be used by only one
extension to receive calls.

DIL 1:1 can have different destinations for day and night modes (Night Service).

Содержание KX-TD500CE

























































































































































































































































































































































































Результаты поиска

Содержание KX-TD500CE

Отзывы:

Panasonic KX-TD500CE, Руководство по функциям, Страница: 114 / 376

Результаты поиска

Содержание KX-TD500CE

Отзывы: