Panasonic KX-FP701ME страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 207

background image

6

KX-FP701ME

2 Warning

2.1.

About Lead Free Solder (PbF: Pb free)

Note:

In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that con-
tains lead.

We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn),
Silver, (Ag), and Copper, (Cu).

This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair
work we suggest using the same type of solder.

Caution

• PbF solder has a melting point that is 50

°

~ 70

°

F, (30

°

~ 40

°

C) higher than Pb solder. Please use a soldering iron with tempera-

ture control and adjust it to 700

°

± 20

°

F, (370

°

± 10

°

C).

• Exercise care while using higher temperature soldering irons.: Do not heat the PCB for too long time in order to prevent solder

splash or damage to the PCB.

• PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100

°

F, (600

°

C).

• When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the

opposite side (See figure, below).

2.1.1.

Suggested PbF Solder

There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper,
(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the manufac-
turer’s specific instructions for the melting points of their products and any precautions for using their product with other
materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.

2.2.

Discarding of P. C. Board

When discarding P. C. Board, delete all personal information such as telephone directory and caller list or scrap P. C. Board.

«
...
4
5
6
7
8
...
»

Содержание KX-FP701ME
















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-FP701ME

Бренд: Janome Страницы: 45

Бренд: Janome Страницы: 32

Бренд: Canon Страницы: 2

Бренд: SunStar Страницы: 35

Бренд: Uchida Yoko Страницы: 25

Бренд: Nobles Страницы: 1

Бренд: Rustibus Страницы: 31

artista 200 Embroidery

Бренд: Bernina Страницы: 43

AMS-210EN-HL1306

Бренд: JUKI Страницы: 12

Бренд: Baby Lock Страницы: 28

Бренд: JUKI Страницы: 128

Бренд: morse Страницы: 9

Deskjet 920c series

Бренд: HP Страницы: 49

fax 1010 series

Бренд: HP Страницы: 62

Compaq Presario,Presario 2140

Бренд: HP Страницы: 12

Compaq Presario,Presario 650

Бренд: HP Страницы: 28

Бренд: HP Страницы: 2

Digital Sender 8100C

Бренд: HP Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды