Panasonic KX-FP362CX, Руководство по обслуживанию

Страница: 47 / 194

6.2.3. SERVICE FUNCTION TABLE
Code Function Set Value Effective
Range
Default Remarks
501 Pause time set X 100 msec 001~600 30 ----------
502 Flash time X 10 ms 01~99 70 ----------
503 Dial speed select 1: 10 pps
2: 20 pps 1, 2 1 ----------
510 VOX time 1:6 sec 2:4sec 1, 2 1 ----------
511 VOX sense 1:High 2:Low 1, 2 1 When the TAM (or EXT TAM) does not stop
recording the ICM because noise is detected on
the telephone line, change this setting to "LOW".
514 Belldetectiontime X100msec 1~9 6 ----------
520 CED frequency select 1:2100 Hz
2:1100 Hz 1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in THE UNIT CAN
COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS (P.78).
521 International mode select 1:ON 2:OFF 1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in THE UNIT CAN
COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS (P.78).
522 Auto standby select 1:ON 2:OFF 1, 2 1 The resolution reverts to the default when
transmission is complete.
523 Receive equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km 1~4 1 When the telephone station is far from the unit or
reception cannot be performed correctly, adjust
accordingly.
524 Transmission equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km 1~4 1 When the telephone station is far from the unit or
transmission cannot be performed correctly, adjust
accordingly.
550 Memory clear See TEST FUNCTIONS (P.49).
533 Setting the number of times that
massage transfer is redialed. 00~99 00~99 03 Selects the number of times that message
transfer is redialed (not including the first dialing).
534 Setting the massage transfer/pager
call redial interval 001~999 sec 001~999 065 Sets the interval of message transfer/pager call
redial.
551 ROM check See TEST FUNCTIONS (P.49).
552 DTMF single tone test 1:ON 2:OFF 1, 2 2 See TEST FUNCTIONS (P.49).
553 Monitor on FAX communication
select 1:OFF
2:PHASE B
3:ALL 1~3 1 Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or not.
554 Modem test See TEST FUNCTIONS (P.49).
555 Scan check See TEST FUNCTIONS (P.49).
556 Motor test 0 See TEST FUNCTIONS (P.49).
557 LED test See TEST FUNCTIONS (P.49).
558 LCD test See TEST FUNCTIONS (P.49).
559 Document jam detection select 1:ON 2:OFF 1, 2 1 See DOCUMENT JAMS - SENDING (P.26).
561 KEY test See TEST FUNCTIONS (P.49).
570 BREAK % select 1:61% 2:67% 1, 2 1 Sets the % break of pulse dialing according PBX.
571 ITS auto redial time set X number of
times 00~99 05 Selects the number of times that ITS is redialed
(not including the first dial).
572 ITS auto redial line disconnection
time set X second 001~999 065 Sets the interval of ITS redialing.
573 Remote turn-on ring number set X number of
rings 01~99 10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
580 TAM continuous tone detection 1:ON 2:OFF 1, 2 1 ON : Stops TAM operation when Dial tone, etc.
are detected.
590 FAX auto redial time set X number of
times 00~99 5 Selects the number of redial times during FAX
communication (not including the first dial).
591 FAX auto redial time disconnection
time set X second 001~999 065 Sets the FAX redial interval during FAX
communication.
592 CNG transmit select 1:OFF
2:ALL
3:AUTO 1~3 2 Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A.
AUTO: CNG id output only when automatic dialing
is performed. OFF: CNG id not output at phase A.
Refer to SOMETIME THERE IS A TRANSMIT
PROBLEM (P.76).
47
KX-FP362CX