Panasonic KX-FP362CX страница 151 Скачать руководство пользователя

Страница: 151 / 194

7.10.2. TELEPHONE MONITOR

1. Function

This is the function when you are not holding the handset
and can hear the caller’s voice from the line.

2. Signal path

Refer to CHECK SHEET (P.104).

7.10.3. HANDSET CIRCUIT

1. Function

This circuit controls the conversation over the handset, i.e.
the transmitted and received voices to and from the
handset.

2. Signal path (Transmission signal)

Refer to CHECK SHEET (P.104).

3. Signal path (Reception signal)

Refer to CHECK SHEET (P.104).

7.10.4. SPEAKER PHONE CIRCUIT

1. Function

The

circuit

controls

the

automatic

switching

the

transmitted and received signals, to and from the telephone
line, when the unit is used in the hands-free mode.

2. Circuit Operation

The speakerphone can only provide duplex.

3. Signal path

Refer to CHECK SHEET (P.104).

7.10.5. MONITOR CIRCUIT

1. Function

This circuit monitors various tones, such as 1 DTMF tone,2
Alarm/Beep/Key tone/Bell.

2. Signal path

a. DTMF MONITOR

(Speaker Operation)

Refer to CHECK SHEET (P.104).

(Handset Operation)

Refer to CHECK SHEET (P.104).

b. ALARM/BEEP/KEY TONE/BELL

Refer to CHECK SHEET (P.104).

7.10. ITS (Integrated Telephone System) AND MONITOR SECTION

7.10.1. GENERAL

During the monitor operation, the speaker output passes through the power amplifier (IC102) [Analog board].

The DTMF signal is output from the modem (IC505: digital board). The alarm tone, the key tone, bell tone, and beep are output
from gate array IC501 (digital board). During a pulse dial operation, the monitor tone is output from gate array IC501.

7.11. ATAS(Automatic Telephone Answering System) SECTION

1. Function

The ATAS main operation is performed by the special IC505 (MODEM). IC522 (FLASH MEMORY)s control signals are input
from ASIC IC501.

a. Greeting/Message Recording

b. ICM Recording

Greeting/Message/ICM play to speaker

d. Greeting/Message/ICM play to Tel Line

e. Vox Detection

2. Signal Path

Refer to CHECK SHEET (P.104).

151

KX-FP362CX

Содержание KX-FP362CX



































































































































































































Результаты поиска

Содержание KX-FP362CX

Отзывы:

Похожие инструкции для KX-FP362CX

Бренды по названию

Популярные бренды

Panasonic KX-FP362CX, Руководство по обслуживанию

Результаты поиска

Содержание KX-FP362CX

Отзывы:

Похожие инструкции для KX-FP362CX

Бренды по названию

Популярные бренды