background image

INSTRUCTION MANUAL

Contact-Type Digital Displacement Sensor / Controller

HG-SC□

MJE-HGSC No.0056-01V

Thank you very much for purchasing Panasonic products. Read this Instruction Man-

ual carefully and thoroughly for the correct and optimum use of this product. Kindly 

keep this manual in a convenient place for quick reference.

WARNING

 

Never use this product as a device for personnel protection.

 

When using devices for personnel protection, use products that meet the laws 

and standards for personnel protection that apply in each region or country, such 

as OSHA, ANSI and IEC.

This document provides a brief summary of mounting, wiring, and other related information.

For detailed information, refer “

our web site (http://panasonic.net/id/pidsx/global)

”.

1

STANDARDS AND REGULATIONS

 

This product conforms to the standards and regulations below.

<European Directives>

EMC Directive

 

Contact for CE

Panasonic Marketing Europe GmbH Panasonic Testing Center

Winsbergring 15, 22525 Hamburg,Germany

2

CONTENTS OF PACKAGE

 Controller 

1 pc.

 Instruction Manual (English / Japanese, Chinese / Korean) 

1 pc. each

 General Information for Safety, Compliance, and Instructions (23 languages) 1 pc.

3

DESCRIPTION OF PARTS

Female connector

Sensor head connection cable connector

Digital display / operation cover

Male connector (Slave unit only)

(Note)

Output 1 indicator (Orange)

Circle meter (Orange, Green)

Copy checkmark (Orange)

Digital display / SUB (Green)

Digital display / MAIN (White)

Status mark (White)

Guide mark (White)

LEFT key UP key

RIGHT key

ENTER key

DOWN key

EXIT key

Output 2 indicator (Orange)

Input indicator (White)

Preset indicator (Green)

Preset key

Output 3 indicator (Orange)

Note: Not included on the slave unit / Wire-saving type 

HG-SC113

.

4

MOUNTING

How to mount

1. 

 Fit the rear part of the mounting section of the 

controller on a DIN rail.

2. 

 Press down the rear part of the mounting sec-

tion of the unit on the DIN rail and fit the front 

part of the mounting section to the DIN rail.

2.

 Press

1.

 Insert

35mm width DIN rail

How to remove

1. 

 Push the controller forward.

2. 

 Lift up the front part of the controller to remove 

it.

2.

 Lift

1.

 Press forward

Connecting the sensor head connection cable

How to mount

1. 

 Insert the sensor head connection cable into 

the connector for the sensor head connection 

cable on the controller.

1.

 Insert

Note:  Insert the connector firmly. Risk of sensor head or controller damage if not completely connected.

How to remove

1. 

 Grasp the controller, and while pressing on 

the release lever on the connector of the sen-

sor head connection cable, pull the cable to-

ward you to disconnect.

1.

 Pull out

Release lever

Note:  Do not pull by holding the cable without pressing the release lever, as this can cause cable break or connector break.

5

CONNECTING SLAVE UNITS

 

 Always shut off the power before connecting a slave unit to or disconnecting a 

slave unit from the master unit. Risk of controller damage if you attempt connec-

tion with the power ON.

 

 Insert the male connector firmly into the female connector. Risk of controller 

damage if not completely connected.

 

 To connect units, the units must be mounted on a DIN rail. Attach end plates  

MS-DIN-E

 (optional) so as to enclose the connected units at the ends.

 

 Up to 15 slave units can be connected per master unit. (When communication 

unit consolidated: up to 14 slave units)

 

When connecting slave units to a master unit, connect only NPN output types, or 

only PNP output types. Dissimilar output types cannot be connected together.

To mount or remove a controller, refer to “

4

MOUNTING

”.

How to connect

1. 

 

Mount one master unit on the DIN 

rail.

2. 

 

Remove the connector cover.

3. 

 

Mount each slave unit one at a time 

on the DIN rail. Remove all connec-

tor covers except for the cover on 

the last end slave unit.

4. 

 

Slide each slave unit and connect 

the female and male connectors.

5. 

 

Attach end plates 

MS-DIN-E

 (op-

tional) with the flat side facing in so 

as to enclose the connected units 

at the ends.

6. 

 Tighten the screws to fasten the 

end plates.

Master unit

Connector cover

Slave unit

Slide

End plate  

MS-DIN-E

 (Optional)

End plate  

MS-DIN-E 

(Optional)

How to remove

1. 

 Loosen the screws on the end 

plate.

2. 

 Remove the end plate.

3. 

 Slide and remove the controllers, 

one at a time.

Slide

6

I/O CIRCUIT DIAGRAMS

Input circuit diagrams

 

NPN output type

*S1

*S1

*S1

(Pink) External input 1

(Violet) External input 2

(Pink / Violet) External input 3

(Blue) 0V (Note 1)

0V

Main circuit

(Brown) + V (Note 1)

+ V

(Black) Output 1

(Gray) Analog current output (4 to 20mA) (Note 2)

(250Ω MAX.)

(Shielded) Analog ground (Note 2, 3)

(White) Output 2

(Black / Gray) Output 3

+

24V DC ±10%

Load

Load

Load

Load

AGND

 

PNP output type

0V

+ V

(250Ω MAX.)

24V DC ±10%

Main circuit

(Brown) + V (Note 1)

*S2

*S2

*S2

(Pink) External input 1

(Violet) External input 2

(Pink / Violet) External input 3

+

(Black) Output 1

(White) Output 2

(Black / Gray) Output 3

(Blue) 0V (Note 1)

Load

Load

Load

(Gray) Analog current output (4 to 20mA) (Note 2)

(Shielded) Analog ground (Note 2, 3)

Load

AGND

*S1

*S2

Non-voltage contact or NPN open collector transistor

or

0 to +1.2V DC: Valid

+8V to +V DC or open: Invalid

Non-voltage contact or PNP open collector transistor

or

+4V to +V DC: Valid

0 to +0.6V DC or open: Invalid

Notes:  1)   The 

HG-SC111□

 and 

HG-SC112□

 cables do not have +V or 0V. Power is supplied from the connector of the 

master unit.

 

2)   The 

HG-SC112□

 cables do not have analog current output or analog ground.

 

3)  Use shielded wire for the analog output.

Отзывы: