Panasonic FV-05-11VKL1 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 12

Panasonic FV-05-11VKL1 Скачать руководство пользователя страница 10

Fig.12

10

CAUTION

CAUTION

WARNING

Fig.13

INSTALLATION (NEW CONSTRUCTION) CONTINUED

INSTALLATION (RETROFIT)

1. Remove the existing fan and cut ceiling openning.

2. Follow the step 1, 4, 5 on page 8 and step 7 on
page 9. (Before connect the circular duct to the
adaptor, should pull down the circular duct from
the ceiling)

Disconnect power source before working
on unit.

5. Follow the step 10 to 16 on page 9 to 10.

TM

Secure the Flex-Z Fast bracket to joists by using 4
tapping screws (ST4.2x20) (Please prepare the

TM

screws and put on Flex-Z Fast bracket before

TM

Flex-Z Fast bracket is installed on joist).
Existing ductwork and wiring left in place. (Fig.14)

TM

3. Install the adaptor to Flex-Z Fast bracket by using
2 self-drilling screws. (Fig.15)

Grille

Ceiling

Gloves

Mounting spring

16. Insert the other mounting spring into the slot
as shown and mount grille to fan body. (Fig.13)

Mount grille carefully so that lead wire of
lighting unit is not pinched.

TM

4. Secure the fan body to Flex-Z Fast bracket by
using 2 self-drilling screws, plug connector to
receptacle and secure the fan body to adaptor
by using machine screw (M4X6). (Fig.16)

Secure machine screw (M4X6) to the suitable

TM

hole and not touch the Flex-Z Fast bracket.
Please fix the screw carefully to avoid screw
slip teeth.

Ceiling

Flange

Joist

Machine screw (M4X6)

2 Self-drilling screws (Fix the

TM

flange and Flex-Z Fast bracket through the ceiling)

15. Adjust Pick-A-Flow switch; if used, adjust the
FV-VS15VK1 Multi-Speed module. (Fig.12)
Refer to indication on page 6.

14. Plug in the specified devices as your choice
(refer to installation on page 8). Insert the
motion sensor (FV-MSVK1 only) or LED night
light (FV-NLVK1 only) into slot of the grille.
Fix the lead wire into the clasp (Fig.11).

CAUTION

Before turn on the light, make sure the
connector at the correct position. If not,
the lighting can’t work.

The claw of connector must latch the rib
completely.

Grille

Ceiling

Fig.11

Ceiling

Motion sensor
(FV-MSVK1 only)

Mounting spring

LED night light
(FV-NLVK1 only)

Gloves

Plug
connector

Inser plug
connector

Lighting
unit

Clasp

Rib

Claw

Fig.15

Mastic or
approved
foil tape

2 Self-drilling screws

Ceiling

Joist

Knock-out
hole

Junction box
cover

Conduit

Circular duct

Fig.14

10 7/8

(275)

10 7/8 (275)

Ceiling (already existed)

Conduit Circular duct

Joist

4 Tapping
screws (ST4.2x20)

Fig.16

Unit: inches (mm)

«
...
8
9
10
11
12
»

Содержание FV-05-11VKL1













Отзывы:

Нет отзывов