Panasonic FP7 CPU Unit Скачать руководство пользователя

Страница: 73 / 92

7.3 Receiving Operation

7.3.3 GPRECV (General-Purpose Communication Receiving Command)



Command format

Setting

item

Settings

Setting range

Specify the operation unit.

US / SS

Specify the initial address of the data area to save the received data.

(Note 1)

Specify the final address of the data area to save the received data.

(Note 2)

(Note 1): Devices that can be specified for D1 are: WX, WY, WR, WL, DT, LD.
(Note 2): Devices that can be specified for D2 are: WX, WY, WR, WL, DT, LD.

KEY POINTS

•

Specify the connection targeted for communication, using UNITSEL

command immediately before GPRECV command.

•

When the general-purpose communication reception done flag is ON for the

targeted connection, execute GPRECV.

7-11

Содержание FP7 CPU Unit





























































































Результаты поиска

Содержание FP7 CPU Unit

Отзывы:

Похожие инструкции для FP7 CPU Unit

Бренды по названию

Популярные бренды

Panasonic FP7 CPU Unit, Руководство пользователя

Результаты поиска

Содержание FP7 CPU Unit

Отзывы:

Похожие инструкции для FP7 CPU Unit

Бренды по названию

Популярные бренды