Panasonic DPC-100 Series, Инструкция по эксплуатации

Страница: 1 / 4

4 WIRING
Connection method
Insert the cable with connector CN-66A-C
into the product’s connector area for a power
Disconnection method
Pressing the release lever of the cable with
Cable with connector
CN-66A-C
Release
lever
Connector area of the cable with
connector
Housing: PAP-06V-S
!"#$%&'
Note: Do not pull by holding the cable without pressing the release lever, as this can cause cable break or connector
(
<Connection connector pin arrangement>
1 2 3 5 4 6
$) Terminal name
1 +V
2 Analogue voltage / current output
3 0V
4 Comparative output 1
5 Comparative output 2
6 External input
5 I/O CIRCUIT DIAGRAMS
When using the analogue voltage output, take care to the input impedance of the
&&*
Furthermore, note that if the cable is extended, the cable resistance will cause the
*&
NPN output type
(Gray) Analogue
voltage / current
output (Note 1, 2, 3)
(Brown) +V
(Black) Comparative output 1
(White) Comparative output 2
(Pink) External input
(Blue) 0V
12 to 24V DC
±10%
+
-
%&
%&
(*1)
Main circuit
PNP output type
(Brown) +V
(Pink) External input
(Black) Comparative output 1
(White) Comparative output 2
(Gray) Analogue
voltage / current
output (Note 1, 2, 3)
(Blue) 0V
%&
%&
(*2)
Main circuit
12 to 24V DC
±10%
+
-
*1 *2
Non-voltage contact, NPN open-collector transistor or
DC 2-wire output
or
High (5 to 30V DC or Open): Invalid
%;<=>?$@J>&
Non-voltage contact, PNP open-collector transistor or
DC 2-wire output
or
High (5V to +V DC): Valid
%;<K>?$@J*&
)JL@Q&&UX<YZ[
U@!(X>Z*
\@Q*#Z&#&&*
]Z#[&&*&
6 OUTPUT MODE AND OUTPUT OPERATION
The EASY mode, hysteresis mode or window comparator mode can be selected as
Z&#Z*L&Z*U
Refer to
<Comparative output 1 / 2 output mode setting> in “ 8 MENU SET-
TING MODE _#&
EASY mode
)]]#Z*&Z&
`J` [&;)L@
When the pressure sensor head is
compound pressure type or posi-
tive pressure type, hysteresis is
&
When the pressure sensor head is
vacuum pressure type, hysteresis
*Z&
Pressure
P
0
ON
OFF
Comparative
output
H (Hysteresis)
Notes: 1) ` [&jq# in “ 9 PRO MODE _#
2) “ ” is displayed for comparative output 1 and “ _#Z*U&
INSTRUCTION MANUAL
Head Separated Digital Pressure Sensor Controller
DPC-100 Series
"z?{$L<<)<<=<|L>
!( * Z#{&q&"
# & #&ZZ#&}& (
Z*#~(#
WARNING
)*&&*#
In case of using devices for personnel protection, use products which meet laws
& && `) z$ # -
&&&##Z"Z
?&&&#*
1 PART DESCRIPTION
Connector area for a power supply /
I-O cable
Connector area for a pressure
sensor head
Output 1 operation
indicator
% Z-
parative output 1 is ON
Output 2 operation
indicator
% Z-
parative output 2 is ON
Mode selection key
Unit display
(Note 1, 2)
Main display
Sub display
Setting value
DOWN key
Setting value UP key
)JL@&
U@!&#& "{_({_
2 MOUNTING
The sensor mounting bracket MS-DP1-6 *QZ
Z(~&
<X)‚Z
M3 (length 6mm) screws
with washers
(Accessory with
MS-DP1-6 )
Sensor mounting bracket
MS-DP1-6 (Optional)
The panel mounting bracket MS-DP1-2 (optional), as well as the front cover MS-DP1-3
;@*
For mounting of the panel mounting bracket, refer to the Instruction Manual en-
closed with MS-DP1-2
3 CONNECTION OF PRESSURE SENSOR HEAD
!&Z ƒ&&
Q&&*Z &
!#Z&*
Connection method
Insert the pressure sensor head cable into
the product’s connector area for the pressure
&
Disconnection method
Pressing the release lever of the pressure
&
Pressure sensor
head cable
Release lever
Connector area of the pressure
sensor head cable
e-con: 1473562-4
! z"{ }'
Note: Do not pull by holding the cable without pressing the release lever, as this can cause cable break or connector
(
<Connection connector pin arrangement>
1 2 3 4
$) Terminal name
1 Sensor head supply voltage
2 Analogue input
3 0V
4 Model discrimination signal