Panasonic CS-PS12JKT Скачать руководство пользователя страница 1

© Panasonic HA Air Conditioning (M) Sdn Bhd 2008. 
Unauthorized copying and distribution is a violation of law.

 

Order No: PHAAM0809089C3 

 

 
 

Indoor Unit 

Outdoor Unit 

CS-PS9JKT 

CS-PS12JKT 

 

CU-PS9JKT 

CU-PS12JKT 

 

 

 

 

 

TABLE OF CONTENTS 

1.

 

Safety Precautions ...........................................3

 

2.

 

Specification.....................................................5

 

3.

 

Location of Controls and Components ...........7

 

3.1

 

Indoor Unit..................................................7

 

3.2

 

Outdoor Unit ...............................................7

 

3.3

 

Remote Control...........................................7

 

4.

 

Dimensions.......................................................8

 

4.1

 

Indoor Unit ................................................. 8

 

4.2

 

Outdoor Unit .............................................. 9

 

5.

 

Refrigeration Cycle Diagram......................... 10

 

6.

 

Block Diagram ............................................... 11

 

6.1

 

CS-PS9JKT CU-PS9JKT ......................... 11

 

6.2

 

CS-PS12JKT CU-PS12JKT...................... 12

 

7.

 

Wiring Connection Diagram.......................... 13

 

WARNING 

This service information is designed for experienced repair technicians only and is not designed for use by the general public. 
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. 
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to 
service or repair the products dealt with in this service information by anyone else could result in serious injury or death. 

 

PRECAUTION OF LOW TEMPERATURE 

In order to avoid frostbit

e

, be assured of no refrigerant leakage during the installation or repairing of refrigerant circuit.

 

Содержание CS-PS12JKT
















































































Отзывы: