manualshive.com logo in svg

Panasonic CS-PC36JKV, Руководство по обслуживанию

Поделиться
Скачать
Panasonic CS-PC36JKV Скачать руководство пользователя страница 1

© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2008.
Unauthorized copying and distribution is a violation of law.

Order No. PHAAM0810074C2

Air Conditioner

Indoor Unit     Outdoor Unit

CS-PC36JKV  CU-PC36JKV

TABLE OF CONTENTS

PAGE

PAGE

1 Safety Precautions

-----------------------------------------------

3

2 Specifications

-----------------------------------------------------

5

3 Features

-------------------------------------------------------------

7

4 Location of Controls and Components

-------------------

8

4.1. Indoor Unit--------------------------------------------------- 8
4.2. Outdoor Unit ------------------------------------------------ 8
4.3. Remote Control -------------------------------------------- 8

5 Dimensions

---------------------------------------------------------

9

5.1. Indoor Unit & Remote Control -------------------------- 9
5.2. Outdoor Unit -----------------------------------------------10

6 Refrigeration Cycle Diagram

--------------------------------

11

7 Block Diagram

----------------------------------------------------

12

8 Wiring Connection Diagram

---------------------------------

13

8.1. Indoor Unit--------------------------------------------------13

8.2. Outdoor Unit----------------------------------------------- 13

9 Electronic Circuit Diagram

-----------------------------------

14

9.1. Indoor Unit ------------------------------------------------- 14
9.2. Outdoor Unit----------------------------------------------- 15

10 Printed Circuit Board

------------------------------------------

16

10.1. Indoor Unit ------------------------------------------------- 16
10.2. Outdoor Unit----------------------------------------------- 18

11 Installation Instruction

----------------------------------------

19

11.1. Select The Best Location ------------------------------ 19
11.2. Indoor/Outdoor UnitInstallation Diagram ----------- 19
11.3. Indoor Unit ------------------------------------------------- 20
11.4. Outdoor Unit----------------------------------------------- 24

12 Operation Control

-----------------------------------------------

29

12.1. Cooling Operation---------------------------------------- 29

Содержание CS-PC36JKV





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды