Panasonic AW-UE50WP, Руководство по эксплуатации, Страница: 94 / 154

„ z
RTMP
Make RTMP/RTMPS transmission settings.
Server setup
The setting is confirmed with the [Set] button.
<NOTE>
• Switch to the appropriate method of registering RTMP/RTMPS
transmission server information suited to the setting information
notified from the RTMP/RTMPS transmission server you are using.
• The Stream Key setting field is displayed only when [Type2] is set.
• When performing RTMP transmissions, set the Server URL and
Stream key acquired from the external application, and then click
the [start] button for [SRT/MPEG2-TS/RTMP] in the live screen
[Live].
• When performing RTMP transmissions, enable connection with the
network in the [Network] screen.
URL type [Type1, Type2]
Select the method for registering the information for the RTMP/
RTMPS transmission server.
Type1 Specify to set the server URL and RTMP/RTMPS stream
key as a set in [Server URL].
Type2 Specify to individually set the server URL and RTMP/
RTMPS stream key in [Server URL] and [Stream Key].
URL
Server URL
Set the URL for the RTMP/RTMPS server to be transmitted to.
Stream key
The stream key obtained from the RTMP/RTMPS server is set
during streaming only when the service is set to [Type2].
Streaming format
Make settings for H.264 images for use in RTMP/RTMPS
transmission.
The setting is confirmed with the [Set] button.
Refer to the explanation for H.264 (→ page 91) for information
about Image capture size, Frame rate and Max bit rate(per client).
<NOTE>
• Streaming format settings cannot be changed during RTMP/RTMPS
transmissions.
• Set the Streaming format to the settings recommended for the
transmission destination server. Visit the publisher’s website or
contact them about the recommended values.
„ z
SRT
Make SRT transmission settings.
<NOTE>
• When starting SRT transmissions in the [Listener] mode, set the
decoder and application to [Client(Caller)] mode and set the following
URL:
srt://[unit’s IP address]:[value set in Client(Caller) port]
• When performing SRT transmissions in the [Client(Caller)] mode,
set the IP address and port number of the decoder and application
to [Destination URI] and [Destination port], and then click the [start]
button for [SRT/MPEG2-TS/RTMP] in the live screen [Live].
• [Passphrase], [Stream ID], etc., can also be specified with options.
Common setup
The setting is confirmed with the [Set] button.
Mode [Client(Caller), Listener]
Selects the method to connect to the SRT compatible decoder or
service.
Client(Caller) Specify the transmission destination IP address and port
number when starting transmission from this unit.
Listener Specify the listener port when awaiting the external
request to start transmission.
Factory settings: Listener
Destination URI
When [Client(Caller)] is set in [Mode], enter the IP address.
Images and audio will be sent to the specified IP address.
Factory settings: 192.168.0.3
<NOTE>
• Only IPv4 can be set as the IP address.
Destination port [1 to 65535]
When [Client(Caller)] is set in [Mode], enter the port number (used
when transmitting images from this unit).
Connection is to the specified port number.
Factory settings: 7002
<NOTE>
• The following port numbers are used by the unit so they cannot be
used.
20, 21, 23, 25, 42, 53, 67, 68, 69, 80, 110, 123, 161, 162, 443, 546,
547, 554, 995, 5960 to 5985, 7960 to 8060, 10669, 10670, 11900,
59000 to 61000
94
Web screen configurations (continued)