Panasonic AJ-PX800G, Руководство по эксплуатации

Страница: 139 / 220

– 139 –
Chapter 6 Menu Operations — Menu list
Item Description of settings
[REC FORMAT] Displays/hides recording format display.
[ON], [OFF]
f
Factory setting: [ON]
[FRAME RATE] Displays/hides frame rate.
[ON], [OFF]
f
Factory setting: [ON]
[ASPECT] Displays/hides letterbox recording display.
[ON], [OFF]
f
Factory setting: [ON]
[ONE CLIP REC] Displays/hides the status of one-clip recording mode.
[ON], [OFF]
f
Factory setting: [ON]
[REC MODE] Displays/hides simultaneous recording mode display.
[ON], [OFF]
f
Factory setting: [ON]
[PROXY] Displays/hides proxy information.
[ON], [OFF]
f
Factory setting: [ON]
[EVF DETAIL] Adjusts the contour of the video in the viewfinder to make it easier to focus.
[ON], [OFF]
f
Factory setting: [OFF]
[EVF PEAK LEVEL] Adjusts the peaking level of the viewfinder.
[ − 7]…[7]
f
Factory setting: [0]
[EVF PEAK FREQ] Adjusts the peaking frequency of the viewfinder.
[HIGH], [LOW]
f
Factory setting: [LOW]
[EVF TYPE] Selects the type of viewfinder to be connected.
[COLOR]: Connects the color viewfinder. (AG-CVF10G, AG-CVF15G)
[B/W]: Connects the black and white viewfinder.
f
Factory setting: [COLOR]
[EVF COLOR] Selects whether to display viewfinder images in color or in black and white.
[ON]: Displays in color.
[OFF]: Displays in black and white.
f
Factory setting: [ON]
[BATTERY SETUP]
Configure the settings for the battery to use.
Item Description of settings
[BATTERY SELECT] Selects the battery to use.
[HYTRON140], [DIONIC HC], [ENDURA10], [PAG L96e]: Detects the battery charge level according to
the selected battery when the HYTRON140, DIONIC HC by Anton/Bauer, ENDURA10 (E-10) by IDX, or
PAG L96e by PAG battery is selected.
[TYPE A], [TYPE B], [TYPE C]:
Select either item when a battery other than [HYTRON140], [DIONIC
HC], [ENDURA10], and [PAG L96e] is used. At this time, set [FULL] (full voltage), [NEAR END] (near end
warning voltage), or [END] (end voltage) in the main menu → [BATTERY SETUP] → [BATTERY SETTING]
(page 140) according to the battery in use.
[BATT STAT]: By selecting [BATT STAT] when using a battery whose charge level is detected as a
percentage value, near end and end operations are conducted according to the percentage value of the
charge level. Set the percentage value of [BATT STAT NEAR END] (near end) and [BATT STAT END]
(end) in the main menu → [BATTERY SETUP] → [BATTERY SETTING] (page 140) according to the
battery in use.
[ENDURA STAT]: Select it when ENDURA battery by IDX is used to perform near end and end operations
according to the percentage value of the charge level information. Set the percentage value of [ENDURA
STAT NEAR END] (near end) and [ENDURA STAT END] (end) in the main menu → [BATTERY SETUP] →
[BATTERY SETTING] (page 140) according to the battery in use.
f
Factory setting: [DIONIC HC]
When the battery charge level percentage cannot be detected even if [BATT STAT] or [ENDURA STAT] is
set, it will follow the setting value of [TYPE A]. Make sure that the [TYPE A] setting values for [FULL] (fully
charged), [NEAR END] (near end), and [END] (end) are appropriate for the battery in use.
[EXT DC IN SELECT] Sets the type of charge level detection when a battery is connected to the <DC IN> terminal. Also detects a
charge level that corresponds to the selected type.
Selection of a battery type is the same as that of [BATTERY SELECT].
Displays the analog voltage in the viewfinder.
[DC PWR SUPPLY], [HYTRON140], [DIONIC HC], [ENDURA10], [PAG L96e], [TYPE A], [TYPE B],
[TYPE C]
f
Factory setting: [DC PWR SUPPLY]
[BATT NEAR END CANCEL] If set to [ON], the warning sound and warning display output can be canceled when the <DISP/MODE
CHK> switch is pushed towards the <CHK> side at battery near end.
[ON], [OFF]
f
Factory setting: [ON]