Panasonic AJ-PX5100G, Руководство по эксплуатации

Страница: 251 / 263

– 251 –
Chapter 9 Maintenance — Warning system
Warning/error displays in the thumbnail operation, menu operation, and USB storage mode
r
Thumbnail and menu
Message Description Measure
[AUTHENTICATION ERROR!] Manual authentication failed. Enter the correct password.
[CANNOT ACCESS!]
Data cannot be accessed due to a content defect or some
other reason.
Ensure the health of the media and the clips.
[CANNOT CHANGE!]
For a clip with the mark, where a thumbnail cannot be
generated, the thumbnail cannot be modified in the text memo
position.
Correct the settings and content to enable display of the
thumbnail.
[CANNOT DELETE!] The content versions do not match. Cannot delete. Match the device and contents version.
[CANNOT FORMAT!] A P2 card problem or some other reason prevents formatting. Check the P2 card.
[CANNOT RE-CONNECT!]
Clips cannot be remerged because either clips not recorded
across multiple P2 cards are selected or other reasons.
Check the selected content.
[CANNOT REPAIR IN
SELECTION!]
Some of the selected clips cannot be repaired. Check the selected content.
[CANNOT REPAIR!] Content that cannot be repaired is selected. Check the selected content.
[CANNOT SAVE!][FILE NAME
IN USE]
A settings file of the same name exists on the SD memory
card.
Use another name to save the file.
[CARD FULL!] The P2 card or SD memory card is full. Insert a card with free space available.
[COPY IMPOSSIBLE. TOO
LARGE CLIP CONTAINED!]
[CLIP NAME:] (clip name)
Files exceeding 4 GB cannot be copied to a P2 memory card
or microP2 memory card with 32 GB or lower capacity.
Copy to a microP2 memory card with capacity larger than
32 GB.
[INVALID VALUE!] The data value you entered is invalid. Enter data within the normal range.
[LACK OF CAPACITY!] There is not enough recording capacity left on the card. Insert a card with sufficient recording capacity.
[MISSING CLIP!]
Shot marks cannot be attached to the clips unless all clips
recorded over multiple P2 cards are present.
Insert all P2 cards over which recording extended.
[NO CARD!] No P2 or SD memory card is inserted. Insert the relevant media.
[NO COPY TO SAME CARD!] A clip cannot be copied to the card storing the original clip.
Copy the selected clip to a card that does not contain the
original clip.
[NO FILE!] The specified file does not exist. Check the file.
[NO INPUT!] No data is entered. Enter data and then set.
[NO SD CARD!] No SD memory card. Insert an SD memory card.
[NOT SELECTED!] Attempted to delete without selecting clips. Select clips to delete.
[SAME CLIP IS SELECTED!]
Multiple instances of the same clip (copies) are included in the
clips selected.
Multiple instances of the same clip (copies) cannot be copied
simultaneously. Remove instances of the same clip from
selected items.
[TOO MANY CLIPS!] Too many clips are selected. Reduce the number of selected clips.
[UNKNOWN CONTENTS
FORMAT!]
This is a warning of the contents for the version that is not
supported by the camera.
Match the device and content versions.
You cannot write back only proxy recording clips from the FTP
server to the P2 card.
Write back (import) proxy recording clips to an SD memory
card.
[UNKNOWN DATA!]
The metadata character code is invalid.
The metadata character code is UTF-8. Enter valid characters
using a viewer.
There is a problem with data in the file. Create the file again.
[USER CLIP NAME MODIFIED!] When adding a counter value to the clip name, characters
must be deleted.
For the counter addition setting, the user clip name plus the
counter value can only contain up to 100 bytes. Characters in
the clip name are automatically deleted when the total number
of characters exceeds this limit.
[WRITE PROTECTED!] The P2 card or SD memory card is write-protected. Insert write-accessible media.
[CANNOT OPERATE THIS
MENU, WHILE "REC DURING
UPLOAD" ENABLED.]
The menu cannot be executed.
Set [DISABLE] in the main menu → [I/F SETUP] → [USB/
LAN] → [FTP CLIENT SERVICE] → [REC DURING UPLOAD]
before execution.
r Soft keyboard
Message Description Measure
[AUTHENTICATION ERROR!] Manual authentication failed. Enter the correct password.
[CANNOT CHANGE!]
An attempt is made to enter the [PERSON] item (user who
enters the memo) when there is no text memo.
Enter the [TEXT] (text information) first.
[CANNOT SET!]
[INVALID VALUE!]
The entered value is invalid. Change the input value.
[CANNOT SET!]
[NO INPUT!]
There is not input to the software keyboard. Enter the password.
[CANNOT SET!]
[RETRY PASSWORD IS
DIFFERENT!]
The re-entered password is different. Enter the correct reference password.