Panasonic AJ-PX5100G, Руководство по эксплуатации, Страница: 107 / 263

– 107 –
Chapter 4 Shooting — Viewfinder status display
20 Time code display
[TCG 12:59:59:20] Displays the time code generator value.
[TCR 12:59:59:20] Displays the time code reader value.
[VUBG AB CD EF 00]
([UBG AB CD EF 00])
Displays the user’s bit generator value.
[VUBR 12 34 56 78]
([UBR 12 34 56 78])
Indicates the user’s bit reader value.
[CTL
−
1:59:59:20] Displays the CTL counter value.
21 Audio input line and level meter display
[---- r ---- + ]
Displays the selected channel and its audio level.
[F] Displayed when the <AUDIO IN> switch is <FRONT>.
[W] Displayed when the <AUDIO IN> switch is <W.L.>.
[R] Displayed when the <AUDIO IN> switch is <REAR>.
22 Iris override display
Displays the compensation level when the iris overwrite is functioning.
[ ++ ]
Aperture opens by about 1.
[ + ] Aperture opens by about 0.5.
[ −− ] Aperture closes by about 1.
[ − ] Aperture closes by about 0.5.
(No display) Reference state.
23 Super iris display
Displayed when super iris is active.
24 Iris, F value
[NC] Displayed when the lens cable is not connected.
[OPEN] Displayed when the lens aperture is open.
[F1.7] to [F16] Displays the lens aperture value.
[CLOSE] Displayed when the lens aperture is closed.
f Displayed when a lens with an aperture value display function is used. Also, flashes when the iris override is variable.
25 Super black display
Displayed when super black is active.
26 Zoom display
[Z00] to [Z99]
Displays the zoom amount. Note, however, that this item is not displayed in the case of lenses without a zoom position return
even if it is set to be displayed.
[Z ** . * mm]
When a serial lens is connected, the display unit can be changed in the main menu → [VF] → [VF INDICATOR] → [ZOOM/
FOCUS].
27 Focus control information
Displays the focus control information with [99] to [00]. When a lens other than a serial lens is connected, the focus control information is not
displayed. When a serial lens is connected, the display unit can be changed in the main menu
→ [VF] → [VF INDICATOR] → [ZOOM/FOCUS].
28 Information display such as interval recording/pre-recording
[i] Displayed before recording starts and after recording ends during interval recording.
[i-REC] (flashing) Displayed during recording in interval recording.
[i-REC] (flashing)
[ ** h ** m/ ** s]
During interval recording standby, displays the standby time until the next recording.
[P-REC] (flashing)
Displayed after recording is stopped and until recording of video/audio to P2 card completely stops. Do not remove the P2 card
or turn the power off until the flashing indication completely goes out.
f When the pre-recording function is set to [OFF], [REC] flashes.
[P-REC
*
s/OFF]
(illuminated)
Illuminated if the <MARKER SEL>/<MODE CHECK/MENU CANCEL> switch is pushed towards the <MCK/MCL> side when the
pre-recording function is set to [ON]. The status is displayed when the <USER> button where [PRE REC] is assigned is pressed
to switch to the pre-recording mode.
[1-CLIP] Displayed when [ONE CLIP REC] is [ON], and a new clip is going to be recorded.
[1 * CLIP]
Displayed when [ONE CLIP REC] is [ON], and recording can be linked to the previous clip.
f If the previous clip no longer exists due to removal of the P2 card or deletion of the clip, the next recording will start as a new
clip. In this case, the display may remain as [1
*
CLIP].
[START 1 * CLIP]
Displayed when recording of a new clip is started in [ONE CLIP REC].
[END 1-CLIP] Displayed when linking of clips is ended in [ONE CLIP REC].
29 Gamma mode display
Displays the gamma mode currently selected by [GAMMA MODE SEL] in the main menu → [PAINT] → [GAMMA].
[HD]/[SD]/[FLK1]/[FLK2]/[FLK3]/[FREC]/[VREC]/[HLG]
30 Lock status display of auto tracking white balance
Displayed when the <USER> button where [ATW LOCK] is assigned is pressed and the color temperature is fixed while auto tracking white balance
is active.